Training

Location:Training / Circuit Fundamentals / Analog / "Analog and Hybrid CMOS Integrated Circuit Design" (Zhejiang University Edition) / basic cmos device physics（10）

You can log in to your eeworld account to continue watching：
basic cmos device physics（10）
Login

Duration：18 minutes and 32 seconds
Date：2018/06/01

Uploader：量子阱

Introduction

keywords： simulation CMOS IC Design

Simulate the process implementation methods, working principles and models of various active and passive devices used in CMOS integrated circuit design. As an excellent analog integrated circuit designer, only after deeply mastering the working principles and characteristics of various devices can we design high-quality analog integrated circuits.

You Might Like

Recommended Posts

Talk about the difference between triode and MOS tube: [p=28, 2, left][color=rgb(51, 51, 51)][font=宋体]In circuit design, if we want to control the current, we can't do without the help of [b]transistors[/b]. The full name of the transistor we commonly cal; qwqwqw2088 Analogue and Mixed Signal

Learn about vector network analysis Smith chart and filter bandwidth measurement!: Vector network analyzer is a magical measuring instrument, its function is very powerful and worth exploring. Today, Boyu Xunming engineers will briefly introduce the Smith chart in the vector network; 博宇讯铭 Test/Measurement

DIY 9B96 Development Board Discussion - Chip: I talked with SOSO this morning, and with the advice of some friends, we can apply for our main chip from TI, so that the cost of our board can be further reduced. It is best to use the school email o; fengzhang2002 Microcontroller MCU

Single power supply problem: Can a triangle wave be obtained with a single power supply? I know that a triangle wave can be obtained by passing a square wave through an integration circuit, but this integration circuit requires a; 达达 Analog electronics

Voltage regulator circuit problem: I connected the circuit as shown in the figure. After power on, Vc=Ui, Ve=0, and Vb is very large. My input voltage is 28V, and the load is 100 ohms. Do I use 1.8K or 1K sampling resistors? Why is the; husthxh Analog electronics

MCU communication finishing post: This post covers three areas of microcontroller communication: serial communication, Ethernet, and USB communication. Everyone is welcome to add to it! [color=red]Serial communication[/color] [color=#; maker MCU

推荐文章

STM32F103学习笔记（1）——FreeRTOS下模拟I2C 2025年02月21日: 一、硬件连接功能口引脚 SCL PB.6 SDA PB.5 二、移植文件链接：https://pan.baidu.com/s/1wxbQTMlnX2pavrbW2RYg4g 提取码：dxex 将 board_i2c.c 和 board_i2c.h 两个文件加入工程的User文件夹下注意：延时函数使用了FreeRTOS的vTaskDelay任务延时函数...

VI-grade推出紧凑型HMI模拟器用于高级人机界面开发 2025年02月19日: 据外媒报道，仿真驱动型汽车开发解决方案供应商VI-grade宣布推出多功能沉浸式工具紧凑型HMI模拟器（COMPACT HMI Simulator），旨在增强汽车内饰人机界面（Human-Machine Interface）系统的开发、评估和测试。图片来源：VI-grade VI-grade的新解决方案独特地将灵活的内部模拟器与实时驾驶仿真相结合，从而可以集成准确...

STM32 软件模拟 IIC 代码，标准库、HAL库可用 2025年02月19日: 1 #ifndef _IIC_H 2 #define _IIC_H 3 4 #include stdio.h 5 #include stm32f1xx_hal.h 6 7 8 /* 定义控制 SDA SCL 的宏标准库版 9 #define I2C_SDA_UP GPIO_SetBits (GPIOC,GPIO_PIN_8) //SDA高电平 1...

STM32 软件复位并模拟USB拔插 2025年02月18日: 最近做了个USB跟上位机的通信，需要软件对MCU进行复位，复位后如果USB没有拔插，PC就不会重新枚举USB为了解决这个问题，我做了软件复位跟，软件模拟USB拔插。 1、软件复位这里我用的是HAL库的软件复位，复位前先把中断关掉，再复位，在你需要复位的代码处添加下面代码即可，代码如下： __set_FAULTMASK(1); //关中断 NVIC_SystemRes...

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号