MAXREFDES1196: 24V/4A DC-DC boost converter using MAX17499B boost controller

The MAXREFDES1196 is a DC-DC boost power supply that delivers up to 4A at 24V from a 10V to 18V supply voltage. It is designed for equipment that needs a high-power, 24V output voltage that is generated from a 12V DC bus.

22W MP-A11 Fixed Frequency Transmitter Reference Design

Single-channel buck converter can drive projector's RGB LEDs by simply adding three power MOSFETs

This application note is an RGB LED driver reference design for a low-power projector. The design features a single MAX16821 HB LED driver to drive the RGB LEDs one at a time. This approach reduces the components needed, resulting in an efficient, small, and economical design. Board layout and test results are shown.

KIT34675EPEVBE: Evaluation Kit - 34675, Single-cell Li-Ion Battery Charger

LED display driver reference design with serial interface

This reference design uses a low-cost MSP430 and two DRV8860 eight-channel low-side drivers to drive eight seven-segment displays with brightness control. The display module benefits from the DRV8860's wide power supply range, high current, PWM brightness control, serial daisy-chain connectivity, and output scalability to hundreds of LEDs. It is a complete solution, equipped with six demonstration display modes via the onboard MCU program, with integrated protection against short circuit, under voltage and over temperature.

Schematic PCB

FRDM-17529EVB: Freedom expansion board - MPC17529, dual H-bridge, stepper motor driver, 2.0V-8.6V, 0.7A

Schematic PCB

TPS40200 Universal Non-Synchronous Buck Converter Reference Design

This reference design operates over an 8V - 16V input range and delivers 5V @ 1A at the output. This design is content from the presentation material of the TI Power Workshop. This design has been built and tested and the design files and test report are included. This is a good low cost design that demonstrates the fundamentals of a non-isolated, non-synchronous dc-dc buck converter.

Schematic PCB

FRDM33771BSPIEVB: Evaluation board for MC33771 with SPI Communication

A_34_V10 Design based on IPS2 motor commutation sensor

Schematic PCB

DER-368 - 190 Watt continuous, 280 Watt peak DC-DC forward converter with standby capability

Schematic PCB

DER-385 - 255W 80 PLUS Platinum Computer Power Supply

Schematic PCB

MOSFET driver IC applications and circuits for TCK401G

Schematic PCB

MC33665 Evaluation Board with CAN FD Gateway and Isolated Daisy Chain Communication

Schematic PCB

Bridgeless PFC power supply basic simulation circuit

DER-720 - 275W PFC front end based on HiperPFS-4 with integrated diode

Schematic PCB

TEA1708DB1168: TEA1708T active X-cap discharge demoboard

Schematic PCB

MAXREFDES1006: High-Efficiency, Current-Mode Synchronous DC-DC Converter with 0.68V/4A Output

The MAX15112 high-efficiency, current-mode step-down regulator with integrated power switches operates from 2.7V to 5.5V and delivers up to 12A of output current in a small 2mm x 3mm package. The MAX15112 offers excellent efficiency with skip mode capability at lightload conditions, yet provides unmatched efficiency under heavy load conditions.

MAXREFDES1249: Tiny Universal Input 36W AC-DC Flyback Converter Using the MAX17595

Flyback converters are the preferred topology in the SMPS (switched-mode power supply) for medium- and low-power range applications because they are simple and economic. They have less components and are efficient in isolating the output from input. They are used in battery-powered applications, universal AC/DC converters, and industrial and telecommunication equipment. Isolated converters traditionally regulate the output voltage and current by utilizing a secondary side regulation (SSR) composed of an optocoupler and secondary error amplifier.

Schematic PCB

MAXREFDES1131: 0.72V/12A power supply for Xilinx Ultrascale+ FPGA

The MAXREFDES1131 provides the internal core voltage (V_CCINT) for Xilinx Ultrascale+ FPGAs. This reference design targets FPGAs with a -2L speed grade that require 0.72V for V_CCINT from a 12V intermediary bus. The converter supports a maximum load of 12A at a 400kHz switching frequency.

Complete IO-Link sensor-transmitter reference design with 24-bit RTD front end

This reference design is a resistance thermometer (RTD) front end with an IO-Link compatible sensor transmitter. This design uses the well-proven IO-LINK PHY and stack, and a 6mm wide form factor (compatible with standard M12 connectors) to quickly start IO-Link device development. TI also provides test results demonstrating the high accuracy of this RTD design (measurement error of 0.17°C over the -200°C to 850°C temperature range). The design also complies with IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 and IEC 60255-5 standards, ensuring reduced time to market for real-world industrial applications. This design comes with a software package that provides a complete solution to speed your sensor transmitter time to market.

Schematic PCB