This board and associated firmware can be used to switch between two serial NMEA GPS feeds based on repair status. The resulting feed is transmitted over a third serial line with RS232 levels. This board is designed around the Cypress PSoC CY8C27143. The PCB is designed using KiCAD.
Portenta X8 is a powerful industrial-grade SOM with a pre-installed Linux operating system onboard and can run device-independent software thanks to its modular container architecture. Securely perform OS/application OTA updates with onboard Wi-Fi/Bluetooth® Low Energy connectivity. It is basically two industrial products combined into one, with a power of no less than 9 cores. Utilize the Arduino environment to perform real-time tasks, while Linux handles high-performance processing. Portenta X8 features NXP® i.MX 8M Mini Cortex®-A53 quad-core up to 1.8GHz per core + 1x Cortex®-M4 up to 400MHz, and STMicroelectronics STM32H747 dual-core Cortex®-M7 up to 480Mhz +M4 32-bit Arm® MCU, up to 240MHz.
Battery-operated fluorescent lighting projects often appeared in hobby electronic magazines in the 1980s. I always thought that fluorescent lamps were devices that only used AC power at that time. Those articles about using batteries to light miniature fluorescent lamps attracted me. I made some fluorescent lights, but I couldn't get good practical use out of them from a lamp efficiency and longevity perspective. That's because I was just reading the article and knew nothing about the theory of discharge lamps or even electronics. I don't know what to change to get good results, and I'm losing interest in it. However I found a battery powered fluorescent light project online that was identical to the schematic I was working on. So I "revived" the project after 30 years with modern driver circuits and correct theory.
In early 2005, NEC Electronics launched small-pin-count microcontrollers such as PIC/AVR based on the 78K0S architecture. The 78K architecture has a register set similar to the i8085 and additional bit manipulation instructions. It is said to be a classic architecture, but the memory organization is simpler than PIC/AVR. There are various devices with dedicated peripherals, and the 78K series occupies a considerable share of industrial equipment. In the early days, only OTP/Mask products were available, so they were not popular among electronic crafts. However, the small pin count 78K series with flash memory is getting some attention from Japanese microcontroller geeks. Powerful IDEs (compilers, assemblers, simulators, etc.) are also provided for free. I built a very simple 78K0S flash programming adapter for these devices. Additionally, I built a universal programming adapter for V850ES, LPCxxxx, STM32F, etc.
The author noticed that the AC line frequency changes in spans of 0.4 Hz and periods of several minutes, so I wanted to examine long-term changes in AC line frequency and voltage. This is a project to build a line voltage frequency monitor. It is not a complete instrument but a simple measurement adapter designed to be embedded in some measurement system with a PC or microcontroller.
During the dry season we often get electrocuted by metal objects, especially door handles. This is due to the charged static electricity in the human body. Any object can be charged, and often objects have electrical potentials of several thousand volts or more. Static electricity often causes malfunction or damage to electronic equipment. I've always wanted to know how much static electricity is carried in an object or human body, so I made a surface potentiometer to measure the potential of a charged object.
Grapevines use a lot of water and the soil dries out quickly, so they need to be watered twice a day. This project is about using an unmanned watering system to water flower pots.
This design mainly explains the circuit and software design of the node equipment, coordinator equipment and gateway equipment in the greenhouse, completes the front-end and back-end interaction between the web page and the WeChat applet, and completes the data transmission test and communication distance test.
This Bilibili small TV uses esp32 as the main control, lvgl GUI interface design, and is developed based on idf4.0 to support smartconfig or WeChat airkiss distribution. Its functions include: network connection display, network acquisition time, weather display, temperature and humidity collection, Fan count display, mqtt temperature and humidity upload, etc. All software and hardware are open source.
Flipper Zero is a portable multi-tool designed for developers and geeks with a toy-like body. It enjoys exploring digital content such as radio protocols, access control systems, hardware, and more. It's completely open source and customizable, so you can extend it in any way you like.
All 12 I/O pins of this design are broken out to 0.1" headers. All 4 TX/RX channels and the reference clock are broken out to SMA connections.
This design is a breakout board for SGMII Gigabit Ethernet PHY DP83867C. It connects to SERDES via a SYZYGY-TXR connector to test and evaluate Ethernet over 1.25Gbps serial channels. 2 channels are used and CDR is required on the RX path. Compared to RGMII, SGMII significantly reduces the number of signals required for routing.
Connect to a 5" LCD paired with a Sipeed Tang Nano. This is an 800x480 LCD with RGB888 connections. All 8 bits of each channel are connected via SYZYGY connectors.
SYZYGY is an FPGA extension standard for medium to high speed interfaces. This design is a splitter for 4x PMOD connectors. All 32 I/O signals from the SYZYGY connector are brought out. 8 on each PMOD.
This design is a plug-in from FLIR's Tau2 LWIR core. Both the LVDS and CMOS channels are connected to the UART configuration channel through the SYZYGY connector.
Plug-in for FLIR's boson LWIR kernel. The 24-bit CMOS channel is connected through the SYZYGY connector along with the UART configuration channel.
SYZYGY is an FPGA extension standard for medium to high speed interfaces. This design is a breakout board for connecting dual Atto320 LWIR sensors. Designed to mate with existing sensor breakout boards that provide FFC connectivity.
SYZYGY is an FPGA extension standard for medium to high speed interfaces. This design breaks out all 32 I/O pins into taps with 0.1" headers. A small prototyping area is also provided.
The design is a custom 3d model from Sensirion. Sensirion provides a 3d model, but it has very few features.
The project is a small desktop-level robot tool that can be used to help you control your computer, etc. Its functions can be defined by you. The inspiration for the appearance design is EVE in WALL-E~ The robot has a USB communication display screen function, has 6 degrees of freedom (one roll and pitch for the hand, one for the neck, and one for the waist), and uses its own modified special servo to support the joints Angle return.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
