Wireless battery-powered smart locks are becoming more and more popular in today's market with the increasing number of building and residential owners looking to retrofit smart locks (or electronic locks) for their buildings or homes. In smart lock applications, high current motors and radios often have a faster battery drain rate, resulting in compromised battery life. Replacing multiple batteries can be time-consuming and costly, so reducing average current draw is often a key design consideration.
DiSEqC 1.x compliant single LNB power and control IC with DSQIN, based on LNBH29, in QFN16 (4x4) package
Due to its simplicity and low cost, the flyback converter is the preferred choice for low-to-medium isolated DC-DC power-conversion applications. However, the use of an optocoupler or an auxiliary winding on the flyback transformer for voltage feedback across the isolation barrier increases the number of components and design complexity.
The PMP20612 reference design is a high efficiency AC-DC LED driver reference design with very low total harmonic distortion (THD). This design uses CCM PFC with the UCC28180 controller to provide power factor correction (PFC) functionality from 108VAC to 305VAC input. A two-switch Flyback converter with the UCC28740 controller is used to provide 200V/1A constant current (CC)/ constant voltage (CV). The voltage sensing and current sensing circuit at the output side with the TL431 and INA180 allow an external circuit to process a dimming function. As a result this design achieves 92.9% peak efficiency at 230VAC/50Hz input. At 277VAC, the board also has less than 20% THD with 20% load.
This reference design is a 120Vac to 17V flyback converter with synchronous rectification on the secondary side. A lossless passive clamp on the primary side helps this reference design achieve greater than 93% maximum load efficiency. When combined with the PMP20172, this reference design becomes a complete solution for a 36W USB Type-C dual-port solution.
DiSEqC 1.X compliant LNB power and control IC based on LNBH25
Power over Ethernet (PoE) is a technology that allows network cables to deliver power to a powered device (PD) through power-sourcing equipment (PSE) or midspan, and has many advantages over traditional methods of delivering power.
6.6 W wide-range input, dual output, isolated flyback converter for anti-magnetizing interference in utility meters using 900 V LinkSwitch-XT2 (LNK3696P)
TEA1936xDB1521
The MAX17681/MAX17681A is a high-voltage, highefficiency, iso-buck DC-DC converter designed to provide isolated power up to 5W.
This application note describes Maxim's UL® Recognized, IEEE® 1394™, single- and dual-port FireWire® protective circuits. The single-port FireWire protective circuit is designed using the MAX5943A, while the dual-port FireWire protective circuit utilizes the MAX5944. To assist designers with implementing these circuits, this application note details the schematics, PCB layout, and bill of materials for each UL Recognized circuit.
Due to its simplicity and low cost, the flyback converter is the preferred choice for low-to-medium isolated DC-DC power-conversion applications. However, the use of an optocoupler or an auxiliary winding on the flyback transformer for voltage feedback across the isolation barrier increases the number of components and design complexity. The MAX17690 eliminates the need for an optocoupler or auxiliary transformer winding and achieves ±5% output voltage regulation over line, load, and temperature variations.
The kit allows evaluation of the NHS3100 chip for treatment compliance and the start of development of specific use cases. This starter kit develops firmware that is fully reusable in the final product form factor, accelerating time to market for treatment-adherence products.
The MAX17595 is a peak-current-mode controller for designing wide input-voltage flyback regulators.
This document details the MAXREFDES128# subsystem reference design, a 36V to 57V input, 5V output, no-opto flyback isolated power supply capable of 12.5W. Design files and test results are included. Hardware is available for purchase.
TI reference design TIDA-01095 has been tested as a DC/DC LED driver subsystem for high-power, high-efficiency dimmable LED luminaires. The design is built on a wireless SoC platform and enables brightness adjustment via analog as well as PWM dimming and control using any Bluetooth Smart device or ZiBee. High-bay and low-bay LED lighting fixtures are set to replace fluorescent and HID lamps as they cut energy consumption in half and virtually eliminate maintenance costs. Harvesting daylight by combining dimming with an ambient light sensor can result in additional energy savings of up to 50%, depending on the application. TI Reference Design TIDA-01095 provides high-efficiency DC/DC conversion that supports dimming, daylight harvesting, and wireless networked lighting control.
The MAX17504 high-efficiency, high-voltage, synchronously rectified step-down converter with dual integrated MOSFETs operates over a 4.5V to 60V input. The converter can deliver up to 3.5A and generates output voltage from 0.9V to 90% VIN. Built-in compensation across the output voltage range eliminates the need for external components. The feedback (FB) regulation is accurate to within ±1.1% over -40°C to +125°C. The devices are available in a compact (5mm x 5mm) TQFN lead (Pb)- free package with an exposed pad. Simulation models are available. The MAX17504 features a peak-current-mode control architecture with a MODE feature that can be used to operate the device in pulse-width modulation (PWM), pulse-frequency modulation (PFM), or discontinuous mode (DCM) control schemes.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
