Specifications are subject to change without notice.
Revised: 08/30/17
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Maximum Ratings
(T
J
= 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Peak Repetitive Off-State Voltage (Note 1)
(Gate Open, Sine Wave 50 to 60 Hz, T
J
= 25 to 125°C)
2N6504
2N6505
2N6507
2N6508
2N6509
On-State RMS Current (180° Conduction Angles; T
C
= 85°C)
Average On-State Current (180° Conduction Angles; T
C
= 85°C)
Peak Non-repetitive Surge Current
(1/2 Cycle, Sine Wave 60 Hz, T
J
= 100°C)
Forward Peak Gate Power (Pulse Width ≤ 1.0 µs, T
C
= 85°C)
Forward Average Gate Power (t = 8.3 ms, T
C
= 85°C)
Forward Peak Gate Current (Pulse Width ≤ 1.0 µs, T
C
= 85°C)
Operating Junction Temperature Range
Storage Temperature Range
I
T
V
DRM
,
V
RRM
50
100
400
600
800
25
16
250
20
0.5
2.0
-40 to +125
-40 to +125
V
(RMS)
A
A
A²s
W
W
A
°C
°C
I
T (AV)
I
TSM
P
GM
P
G(AV)
I
GM
T
J
T
stg
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
1. V
DRM
and V
RRM
for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative
potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
Thermal Characteristics
Rating
*Thermal Resistance, Junction to Case
*Maximum Lead Temperature for Soldering Purposes, 1/8” from case for
I used the official LED example. I wanted to test the PLL, so I added a top-level file and instantiated the original LED and the newly added PLL. When synthesizing, it prompted ERROR (EX0320): Can not...
I don't know if it's appropriate to post this here. I don't understand, 1. How to identify the moving part on the chip core. How to analyze the mode of the moving part. 2. According to some informatio...
At the end of 2021, the operator-customized set-top box solution that Garbage Man loved was upgraded from the 28nm S905 series to the 12nm S905L3A (S905X2 vest).
Take the E900V22D I bought as an examp...
The name is a bit complicated, I don't know if I can explain the problem clearly. The upper-level application sets the wait event first, and then initiates continuous DMA. When a DMA interrupt comes, ...
Product Features:
Powered by fuel inside the "cell"Using carbon nanotubesAdded an ion pump
Applications:
Can be used to create new human-machine interfaces
Scientists have implanted a nanometer-sized ...
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
TMC428 is a stepper motor motion controller from TRINAMIC. It can reduce the workload of motor control software design and development costs. The 3-axis stepper motor drive control system based on ...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
Stepper motors, also called steppers, use the principles of electromagnetism to convert electrical energy into mechanical energy and have been used since the 1920s. With the increasing popularity o...[Details]
1 Causes of problems with electric vehicle batteries
1.1 Caused by the battery itself
Why do we say that? In the previous issue, we learned about the working princi...[Details]
Lithium iron phosphate batteries are used as lithium-ion secondary batteries. Their main application is now in power batteries, which have great advantages over NI-H and Ni-Cd batteries.
Lithi...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
