Measured with a Micro ohm meter 34420A(Agilent) or 3541(HIOKI) or equivalent. The measurement point of DCR is side of terminal. (refer to the Picture-1)
： 定格電流（インダクタンス変化に基づく場合）又は定格電流（温度上昇に基づく場合）の
測定箇所
½れか小さい方の直流電流値とします。
measurement point
：
Value defined when DC current flows and Rated Current (Based on Inductance Change)
or when current flows and Rated Current (Based on Temperature rise) whichever is smaller.
： 定格電流（インダクタンス変化に基づく場合）とは½ﾝﾀﾞ½ﾀﾝ½½が初期値より
30% ½下した時の電流値。
(周囲温度 20℃)
：
The DC saturation allowable current value is specified when the decrease of the
initial inductance value at 30%.(The ambient reference temperature is 20℃）
： 定格電流（温度上昇に基づく場合）とは、直流を流した時の½品温度上昇が
40℃に達する電流値。 （周囲温度20℃)
：
Rated Current (Based on Temperature rise) is specified when temperature of the inductor
is raised 40℃ by DC current.
( The ambient reference temperature is 20
℃)
*特に指定がない限り、測定は標準状態で行う。
Unless
otherwise specified, measurement is the standard atmospheric conditions.
Picture-1
（4）絶対最大電圧
： 絶対最大電圧は30V DC です。
Absolute maximum voltage
：
Absolute maximum voltage 30Ｖ DC.
Reference Only
FDVE0630 Type
一般仕様
General Specifications ( 1/3 )
項 目
Item
1 たわみ強度
Bending test
3/8
規 格
Specification
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L
:
within ± 5%
条 件
Condition
矢印の方向に曲げ幅 2mmになるまで毎秒約 0.5mmの速さで
加圧し 30±5秒間保持する。
Apply pressure gradually in the direction of the arrow at a rate of about
0.5mm/s until bent depth reaches 2mm and hold for 30±5 s.
基板
Board : 40
×
100mm
厚さ
thickness 1.0mm
2 固着強度
Adhesion strength
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L
:
within ± 5%
3 耐振性
Vibration
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L
:
within ± 5%
4 耐衝撃性
Mechanical shock
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L
:
within ± 5%
5 自由½下試験
Free fall test
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L
:
within ± 5%
6 はんだ付け性
Solderability
浸漬した電極面の 90%
以上新しいはんだで覆わ
れている事。
New solder shall cover
90% minimum of the surface
immersed.
初期値に対する
Lの変化率 ± 7%以内
R0.5の押し治具を½用して、矢印の方向に
静荷重を加え60±5秒間保持する。
測定は、荷重を取り去った後に行なう。
A static load using a R0.5 pressing tool shall be applied
to the body of the specimen in the direction of the arrow and
shall be hold for 60±5 s. Measure after removing pressure.
掃引の割合 10½55½10Hz/分、全振幅 1.5mm
X½Y½Z 方向に各 2時間（計 6時間）加える。
The specimen shall be subjected to a vibration of 1.5mm
amplitude, sweep frequency 10½55Hz(10Hz to 55Hz to 10Hz
in a period of one minute) for 2 h in each of 3(X, Y, Z) axes.
加速度
Peak acceleration
½用時間
Duration of pulse
3方向に各 3回（計 9回）
：
981 m/s
2
：
6 ms
：
3 times in each of 3(X, Y, Z) axes.
Three successive shock shall be applied in the perpendicular
direction of each surface of the specimen.
供試品を取り付けた試験基板を、質量 200g の治具に
取り付け,高さ 1m から堅い木版上に、互いに垂直
な3方向に、各3回（計 9回）自然½下させる。
The specimen must be fixed on test board. It must be equipped with
instruments of which weight is 200g. Then it shall be fallen freely
from 1m height to rigid wood 3 times in each of three axes.
電極に常温にてﾌﾗ½½½½を塗布し下記条件にて
ﾌﾟﾘﾋ½ﾄ後試料全½をはんだ½に浸漬する。
Electrode shall be immersed in flux at room temperature
and then shall be immersed in solder bath after preheat.
245±5℃ , 3±1s
・はんだ付け
Soldering
試験方法
Test method
ﾘﾌﾛ½はんだ
Reflow soldering method
・ﾌﾟﾘﾋ½ﾄ
Preheat
150½180℃ , 90±30 s
・ﾋﾟ½½温度
Peak temp. 250(+5,-0)℃ ( 230℃min , 30±10 s )
試料を板厚0.8mm½ﾞﾗ½½½ﾎﾟ½½基板に½き、上記
条件にてﾘﾌﾛ½炉を2回通す。
The specimen shall be subjected to the reflow process
under the above condition 2 times.
Test board shall be 0.8 mm thick. Base material shall
be glass epoxy resin.
測定
Measurement
常温常湿中に1時間放½後測定。
The specimen shall be stored at standard atmospheric
conditions for 1 h in prior to the measurement.
7 はんだ耐熱性
Resistance to
soldering heat
Change from an initial value
L
:
within ± 7%
FDVE0630
Reference Only
FDVE0630 Type
一般仕様
General Specifications ( 2/3 )
項 目
Item
8 耐電圧
Dielectric strength
9 耐寒性
Low temperature
4/8
規 格
Specification
異常がないこと。
Without damage.
初期値に対する
Lの変化率 ± 5%以内
Change from an initial value
L : within ± 5%
条 件
Condition
端子・½½間に DC50V を 1分間印加。½ﾝ½½電流は5mA。
50V DC shall be applied for 60 s between the terminal and the core.
Cut off current 5mA.
温度-40±3℃中に 500±12時間放½後常温常湿中に
1時間放½し、1時間以内に測定。
The specimen shall be stored at a temperature of -40±3℃
for 500±12 h. Then it shall be stabilized under standard
atmospheric conditions for 1 h before measurement.
Measurement shall be made within 1 h.
温度+100±2℃中に 500±12時間放½後常温常湿中に
1時間放½し、1時間以内に測定。
The specimen shall be stored at a temperature of 100±2℃
for 500±12 h. Then it shall be stabilized under standard
atmospheric conditions for 1 h before measurement.
Measurement shall be made within 1 h.
温度60±2℃、湿度90½95%中に 500±12時間放½後
常温常湿中に1時間放½し、1時間以内に測定。
The specimen shall be stored at a temperature of 60±2℃
with relative humidity of 90½95% for 500±12 h. Then it shall be
stabilized under standard atmospheric conditions for 1 h
before measurement. Measurement shall be made within 1 h.
-40℃(30分)→常温(2分以内)→100℃(30分)→常温
(2分以内)を1½½½ﾙとし、これを 500½½½ﾙ行い、
常温常湿中に1時間放½し、1時間以内に測定。
The specimen shall be subjected to 500 continuous cycles
of temperature change of -40℃ for 30 min and 100℃ for
30 min with the transit period of 2min or less. Then it shall be
stabilized under standard atmospheric conditions for 1 h
before measurement Measurement shall be made within 1 h
China Jiangxi Network, March 18 (reported by Huang Haitao) Recently, the reporter received an exciting good news from the largest host domain name and website development and construction service prov...
[i=s]This post was last edited by dontium on 2015-1-23 11:23[/i] [align=left][color=#000][font=宋体][size=12px]Author: TI Expert Bruce Trump[/size][/font][/color][/align][align=left][color=#000][font=宋体...
The project requires recording the power-on time and power-off time of the equipment. Because it needs to run for more than 20 years, it is not recommended to use the RTC+backup battery solution. If t...
Telling beginners about my experience of learning single-chip microcomputers (ZT) The first time I heard the word "single-chip microcomputer" was in 1997. At that time, I was still in technical second...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
