CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on S
X
, D
X
, EN or A
X
exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
4.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
[i=s]This post was last edited by paulhyde on 2014-9-15 09:47[/i] Notes on the Undergraduate Electronic Design Competition (1) The Undergraduate Electronic Design Competition will begin at 8:00 on Sep...
[i=s]This post was last edited by liyiui on 2017-10-22 11:59[/i] The CH554 development board is relatively large and has 3 USB ports When the CH554 is connected to the computer via a USB cable, the se...
TI Signal Chain and Power QA Series Live Broadcast - Sensor Special Live Broadcast with Prizes in Progress!Click here to enter the live broadcastLive broadcast time: July 1, 2022 (today) 10:00-11:30 a...
Hello, forum friends, I just finished learning 51, and now I have a lpc1788 board and a 4.3-inch screen. When I convert the picture into a C file, it can be displayed, but the C file is more than 1Mb....
[i=s] This post was last edited by dcexpert on 2018-7-30 22:21 [/i] There are multiple ways to update ESP32: [list] [*][b]Use the official FLASH_DOWNLOAD_TOOLS[/b] [*][b]Use esptool.py[/b] [*][b]Use D...
I have been working on MMA7455 these days, and I found a strange problem! It is about 3-axis calibration. I looked at the application manual of AN3745, which gives the calibration method, but it only ...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
