PJ4800 Series
400mA Low Dropout Voltage Regulators
T
he series of fixed-voltage monolithic micropower voltage
regulators is designed for a wide range of applications.
voltage (Typ. 60mV al light load and 600mV at 400mA).
This includes a tight initial tolerance of 0.5% typ., extremely
good load and line regulation of 0.05% typ., and very low
output temperature coefficient.
This series is offered in 3-pin TO-263, TO-220, TO-252 &
SOT-223 package, and in 5-pin TO-220 & TO-263 package
with shutdown input.
Thes device excellent choice fo use in battery-power
application. Furthermore, the quiescent current increases on
slightly at dropout, which prolongs battery life.
This series of fixed-voltage regulators features very low
quiescent current ( 100mA Typ.) and very low drop output
______________________________________________________________
______________________________________
FEATURES
•
•
•
•
•
•
Output accuracy within 2% at over timperature
Very low quiescent current
Low dropout voltage (400mV Typ)
Extremely tight load and line regulation
Very low temperature coefficient
Unregulated DC input can withstand -20V reverse battery
and +60V positive transients
•
Avaiable Output Voltage 5V, 3.3V, 2.5V, 1.8V
SOT-223 / TO-252
TO-220 / TO-263
TO-220-5L
TO-263-5L
PIN 1. Input
2. Ground
3. Output
PIN 1. Error
2. Input
3. Ground
4. Output
5. Shutdown
APPLICATIONS
•
•
•
•
•
•
High-efficiency linear regulator
Battery powered systems
Portable instrumentation
Portable consumer equipment
Portable / Palm top / Notebook computers
Automotive electronics
SMPS Post-Regulator
ORDERING INFORMATION
Device
PJ48xxCZ-5L
PJ48xxCM-5L
PJ48xxCZ
PJ48xxCM
PJ48xxCP
PJ48xxCW
xx- output voltage
Operating Temperature
Package
TO-220-5L
TO-263-5L
TO-220
TO-263
TO-252
SOT-223
-20℃ to +85℃
•
ABSOLUTE MAXIMUM RATINGS
Power Dissipation
Lead Temperature (Soldering, 5 seconds)
Storage Temperature Range
Operating Junction Temperature Range
Input Supply Voltage
Continuous total dissipation at 25℃ free-air temperature
TO-220/TO-263
TO-252
SOT-223
1-6
Internally Limited
260℃
.-65 to +150℃
-55 to +150℃
-20 to +35V
2W
1W
0.8W
2002/01.rev.A
PJ4800 Series
400mA Low Dropout Voltage Regulators
ELECTRICAL CHARACTERISTICS at
Vin = 14.4V, Ta = 25℃, I
L
= 5mA, C
o
= 100μF, unless otherwise noted.
Parameter
Conditions
T
J
=25
℃
Full Operating Temperature
1mA≤ I
L
≤700mA,
T
J
≤
T
JMAX
(Note 1)
13V≤V
in
≤26V
1mA≤I
L
≤700mA
I
L
=100mA
I
L
=400mA
I
L
=100μ
A
I
L
=400mA
V
in
=Vout-0.5V, I
L
=100μA
V
out
=0
C
L
=2.2μF
C
L
=3.3μF
C
L
=33μF
(Note 3)
Min
Typ
Max
UNITS
Output Voltage
Output Voltage
Input Supply Voltage
Output VoltageTemperature Coefficient
Line Regulation (Note 2)
Load Regulation (Note 2)
Dropout Voltage (Note 4)
Ground Current (Note 5)
Dropout Ground Current (Note 5)
Current Limit
Thermal Regulation (Note 6)
Output Noise,
10Hz to 100KHz,
I
L
=400mA
Adjust Model
Reference Voltage
Reference Voltage
Feedback Pin Bias Current
Reference Voltage Temperature
Coefficient
Feedback Pin Bias Current Temperature
Coefficient
Shutdown Input
Input Logic Voltage
Shutdown Pin Input Current
Regulator Output Current in Shutdown
0.980|Vo|
0.970|Vo||
0.965|Vo|
5.0 / 3.3
2.5 / 1.8
50
0.1
0.1
200
400
100
30
200
700
0.05
500
350
120
1.21
1.185
1.235
20
50
0.1
1.020|Vo|
1.030|Vo|
1.035|Vo|
26
150
0.4
0.3
300
600
200
40
300
900
0.2
V
V
V
ppm/
℃
%
%
mV
mV
μ
A
mA
μ
A
mA
%W
μ
Vrms
Over Temperature (Note 7)
(Note 1)
1.26
1.285
40
V
V
nA
ppm/
℃
nA/℃
Low (Regulator ON)
High (Regulator OFF)
Vs = 2.4V
Vs = 26V
(Note 8)
0.7
2
30
450
50
600
200
V
μA
μA
Note 1: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the tatal
temperature range.
Note 2: Regulations is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output
voltage due to heating effects are covered under the specification for thermal regulation.
Note 3: Line regulation is tested at 125℃ for I
L
= 5mA. For I
L
= 100μA and T
J
= 125℃, line regulation is guaranteed by desigh to
0.2%. for 13V
≤
V
in
≤26V.
Note 4: Dropout voltage is defined as the input to output differential at which the output voltage drops2% below its nominal value
measured at 1V differential.
Note 5: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin
current and output load current.
Note 6: Thermal regulation is the change in output voltage at a time T after a change in power dissipation, excluding load or line
regulation effects. Specifications are for a 200mA load pulse(3W pulse) for T = 10ms.
Note 7: Vref
≤
Vou t≤ (Vin-1V), 2.3V
≤
Vin
≤26V,
100μA
≤
I
L
≤
400mA,
T
J
≤
T
JMAX
.
Note 8: 2V
≤
Vshutdown, Vin
≤
26V, Vout = 0V
2-6
2002/01.rev.A
京公网安备 11010802033920号
EEWORLD
