2. A 0.1µF bypass capacitor should be placed as close as possible to each positive power pin (<0.2”). If these bypass capacitors are not close to the pins their
high frequency filtering characteristics will be cancelled by the lead inductance of the traces.
3. AVDD and VDD pins must be connected to a power supply level that is at least equal or higher than that of VDDQA, VDDQB, and VDDQC power supply pins.
2.5V or 3.3V, 200 MHz, 12-Output Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
3 of 16
September 2006
rev 0. 4
‘SpreadTrak’
Many systems being designed now utilize a technology
called Spread Spectrum Frequency Timing Generation.
PCS5I9773 is designed so as not to filter off the Spread
Spectrum feature of the Reference Input, assuming it
exists.
PCS5I9773
When a zero delay buffer is not designed to pass the
Spread Spectrum feature through, the result is a
significant amount of tracking skew which may cause
problems in the systems requiring synchronization.
Table 1: Frequency Table
Feedback
Output Divider
÷4
÷6
÷8.
÷10
÷12
÷16
÷20
÷24
÷32
÷40
VCO
Input Clock * 4
Input Clock * 6
Input Clock * 8
Input Clock * 10
Input Clock * 12
Input Clock * 16
Input Clock * 20
Input Clock * 24
Input Clock * 32
Input Clock * 40
Input Frequency Range
(AVDD = 3.3V)
50MHz to 125MHz
33.3MHz to 83.3MHz
25MHz to 62.5MHz
20MHz to 50MHz
16.6MHz to 41.6MHz
12.5MHz to 31.25MHz
10MHz to 25MHz
8.3MHz to 20.8MHz
6.25MHz to 15.625MHz
5MHz to 12.5MHz
Input Frequency Range
(AVDD = 2.5V)
50MHz to 95MHz
33.3MHz to 63.3MHz
25MHz to 47.5MHz
20MHz to 38MHz
16.6MHz to 31.6MHz
12.5MHz to 23.75MHz
10 MHz to19MHz
8.3MHz to 15.8MHz
6.25MHz to 11.8MHz
5MHz to 9.5MHz
Table 2. Function Table (Configuration Controls)
Control
REF_SEL
TCLK_SEL
VCO_SEL
PLL_EN
INV_CLK
Default
1
1
1
1
1
TCLK0, TCLK1
TCLK0
0
PECL_CLK
1
TCLK1
VCO÷1
(high input frequency range)
PLL enabled. The VCO output
connects to the output dividers
QC2 and QC3 are inverted
(180° phase shift) with respect to
QC0 and QC1
Outputs enabled
VCO÷2 (low input frequency range)
Bypass mode, PLL disabled. The input clock connects to
the output dividers
QC2 and QC3 are in phase with QC0 and QC1
Outputs disabled (three-state) and reset of the device.
During reset/output disable the PLL feedback loop is open
and the VCO running at its minimum frequency. The device
is reset by the internal power-on reset (POR) circuitry
during power-up.
MR#/OE
1
2.5V or 3.3V, 200 MHz, 12-Output Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
4 of 16
September 2006
rev 0. 4
Table 3. Function Table (Bank A)
VCO_SEL
0
0
0
0
1
1
1
1
PCS5I9773
Table 5. Function Table (Bank C)
QA(0:3)
÷8
÷12
÷16
÷24
÷4
÷6
÷8
÷12
SELA1
0
0
1
1
0
0
1
1
SELA0
0
1
0
1
0
1
0
1
VCO_SEL
0
0
0
0
1
1
1
1
SELC1
0
0
1
1
0
0
1
1
SELC0
0
1
0
1
0
1
0
1
QC(0:3)
÷4
÷8
÷12
÷16
÷2
÷4
÷6
÷8
Table 4. Function Table (Bank B)
VCO_SEL
0
0
0
0
1
1
1
1
Table 6. Function Table (FB_OUT)
QB(0:3)
÷8
÷12
÷16
÷20
÷4
÷6
÷8
÷10
SELB1
0
0
1
1
0
0
1
1
SELB0
0
1
0
1
0
1
0
1
VCO_SEL FB_SEL2 FB_SEL1 FB_SEL0 FB_OUT
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
÷8
÷12
÷16
÷20
÷16
÷24
÷32
÷40
÷4
÷6
÷8
÷10
÷8
÷12
÷16
÷20
Absolute Maximum Conditions
Parameter
VDD
VDD
V
IN
V
OUT
V
TT
LU
R
PS
T
S
T
A
T
J
Ø
JC
Ø
JA
ESD
H
FIT
Description
DC Supply Voltage
DC Operating Voltage
DC Input Voltage
DC Output Voltage
Output termination Voltage
Latch-up Immunity
Power Supply Ripple
Temperature, Storage
Temperature, Operating Ambient
Temperature, Junction
Dissipation, Junction to Case
Dissipation, Junction to Ambient
ESD Protection (Human Body Model)
Failure in Time
Condition
Functional
Relative to VSS
Relative to VSS
Functional
Ripple Frequency < 100 kHz
Non-functional
Functional
Functional
Functional
Functional
Manufacturing test
Min
-0.3
2.375
-0.3
-0.3
200
-65
-40
Max
5.5
3.465
VDD+ 0.3
VDD+ 0.3
VDD ÷2
150
+150
+85
+150
23
55
10
Unit
V
V
V
V
V
mA
mVp-p
°C
°C
°C
°C/W
°C/W
V
ppm
2000
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
2.5V or 3.3V, 200 MHz, 12-Output Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
[p=24, null, left]The last blog introduced the oled screen using the spi interface on the raspberry pi. Today, I will use that screen on the beaglebone black (BBB) to make the beaglebone black have a ...
Keil compilation warning: Warning: lora_driver.h(10): warning: #1-D: last line of file ends without a newline Reason: The last line of code in the h file does not have a carriage return. Solution: The...
GH-718 human body induction module ■ Application range ■ Security products ■ Human body induction toys ■ Human body induction lamps ■ Industrial automation control, etc. Main technical parameters: 1 W...
My s3c2440 400Mhz slc nandflash reads and writes 3/0.8M/s in wince. You can test it. I use evc to create a file and then write and read, record the time to get this speed...
Many ISP download software can burn AT89S52. Are their hardware circuits different? Do they have dedicated ISP chips (if so, can you give some examples)? Also, where can I download USBISPEasy software...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]