MK3732-08
ADSL Clock Source
Description
The MK3732-08 is a low cost, low jitter, high
performance VCXO and PLL clock synthesizer
designed to replace expensive discrete VCXOs and
multipliers. The on-chip Voltage Controlled Crystal
Oscillator (VCXO) accepts a 0 to 3.3 V input voltage to
cause the output clocks to vary by ±100 ppm. Using
ICS/MicroClock’s patented VCXO and analog/digital
Phase-Locked Loop (PLL) techniques, the device
uses an inexpensive 17.664 MHz or 24.576 MHz
pullable crystal input to produce one or two output
clocks.
ICS manufactures the largest variety of xDSL clock
synthesizers for all applications. Consult ICS to
eliminate VCXOs, crystals and oscillators from your
board.
Features
• Packaged in 20 pin SSOP (QSOP)
• Replaces a VCXO and oscillator
• Uses an inexpensive pullable crystal
• On-chip patented VCXO with pull range of
230 ppm (±115 ppm) minimum
• VCXO tuning voltage of 0 to 3.3 V
• Advanced, low power, sub-micron CMOS process
• 3.3V operating voltage
• Available in industrial temperature range
Block Diagram
VDD
GND
S2:S0
REFEN
PD
VIN
X1
3
Output
Buffer
Output
Buffer
CLK1
PLL/Clock
Synthesis
Circuitry
Voltage
Controlled
Crystal
Oscillator
CLK2
17.664 MHz
or 24.576 MHz
pullable
crystal
Output
Buffer
REF
X2
OE
MDS 3732-08 C
1
Revision 091201
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408) 295-9800 tel • (408) 295-9818 fax • www.icst.com
MK3732-08
ADSL Clock Source
Pin Assignment
X1
NC
VDD
VDD
VDD
VIN
GND
GND
GND
PD
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
X2
NC
S1
REF
REFEN
S0
OE
S2
CLK2
CLK1
Clock Select Table
S2
0
0
0
0
0
0
1
1
1
1
1
1
S1
0
0
0
1
1
1
0
0
0
1
1
1
S0
0
M
1
0
M
1
0
M
1
0
M
1
Input
24.576 *
17.664
17.664
17.664
17.664
17.664
17.664
17.664
17.664
17.664
17.664
17.664
CLK1
2.208
20.00
20.19
70.66
70.66
58.88
35.328
2.208
20.19
4.04
35.328
35.328
CLK2
OFF
OFF
35.328
35.328
35.328
35.328
52.992
35.328
OFF
35.328
61.82
56.52
20 pin (150 mil) SSOP
Pin Descriptions
Number Name Type Description
1
2, 19
3, 4, 5
6
7, 8, 9
10
11
12
13
14
15
16
17
18
20
X1
NC
VDD
VIN
GND
PD
CLK1
CLK2
S2
OE
S0
REFEN
REF
S1
X2
XI
-
P
VI
P
O
O
0=connect directly to GND; M=leave unconnected (floating);
1=connect directly to VDD
* In this mode, 12.288 MHz is present on REF
Crystal connection. Connect to a pullable crystal of 17.664 MHz or 24.576 MHz..
No Connect. Do not connect anything to this pin.
Power Supply. Connect to +3.3V.
Voltage Input to VCXO. Zero to 3.3V signal which controls the VCXO frequency.
Connect to ground.
Clock Output #1 per table above.
Clock Output #2 per table above.
I(PU) Power Down active low. Turns entire chip off, clocks stop low.
I(PU) Select input #2. Selects outputs per table above.
I(PU) Output Enable. Tri-states outputs when low.
TI
O
XO
Select input #0. Selects outputs per table above.
Reference Clock Output. This is the crystal oscillator output clock.
Crystal connection. Connect to a pullable crystal of 17.664 MHz or 24.576 MHz.
I(PU) Reference Clock Enable. Enables REF Output when low. Connect to VDD for lowest jitter.
I(PU) Select input #1. Selects outputs per table above.
Key: I(PU) = Input with internal pull-up resistor; TI = Tri-level Input; O = Output; P = Power Supply Connection;
VI = Analog Voltage Input; XI, XO = Crystal Pins.
External Components
The MK3732-08 requires a minimum number of external components for proper operation. Decoupling capacitors of
0.01µF should be connected between VDD and GND pins 3 and 7, pins 4 and 8, and pins 5 and 9, as close to the
MK3732-08 as possible. A series termination resistor of 33
Ω
may be used for each clock output. The input crystal
must be connected as close to the chip as possible. The input crystal should be a fundamental mode, parallel
resonant, pullable, AT cut.
Consult ICS for recommended suppliers. IMPORTANT - Consult the Application Note MAN05 for layout guidelines.
MDS 3732-08 C
2
Revision 091201
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408) 295-9800 tel • (408) 295-9818 fax • www.icst.com
MK3732-08
ADSL Clock Source
Electrical Specifications
Parameter
Conditions
Minimum
Typical
Maximum
Units
ABSOLUTE MAXIMUM RATINGS (note 1)
Supply voltage, VDD
Referenced to GND
7
V
Inputs and Clock Outputs
Referenced to GND
-0.5
VDD+0.5
V
Ambient Operating Temperature
Commercial version
0
70
°C
Industrial version
-40
85
°C
Soldering Temperature
Max of 10 seconds
260
°C
Storage temperature
-65
150
°C
DC CHARACTERISTICS (VDD = 3.3V unless noted)
Core Operating Voltage, VDD
3.14
3.3
3.46
V
Input High Voltage, VIH, binary inputs
2
V
Input Low Voltage, VIL, binary inputs
0.8
V
Input High Voltage, VIH, trinary input
S0, pin 15
VDD-0.5
V
Input Low Voltage, VIL, trinary input
S0, pin 15
0.5
V
Output High Voltage, VOH
IOH=-12mA
2.4
V
Output Low Voltage, VOL
IOL=12mA
0.4
V
Output High Voltage, VOH, CMOS level
IOH=-4mA
VDD -0.4
V
Operating Supply Current, IDD
No Load
19
mA
Short Circuit Current
Each output
±50
mA
Input Capacitance
S2:S0, OE
5
pF
Frequency synthesis error
Both clocks
0
ppm
VIN, VCXO control voltage
0
3.3
V
AC CHARACTERISTICS (VDD = 3.3V unless noted)
Input Crystal Frequency
17.664
24.576
MHz
Output Clock Frequency
2.208
70.656
MHz
Output Clock Rise Time
0.8 to 2.0V
1.5
ns
Output Clock Fall Time
2.0 to 0.8V
1.5
ns
Output Clock Duty Cycle
At VDD/2
40
60
%
Maximum Absolute Short Term Jitter
15 pF load at output
±125
ps
Phase Noise, relative to carrier
10 kHz offset, no REF
-115
dBc/Hz
Output pullability, note 2
0V < VIN < 3.3V
±115
ppm
Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the
device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may
affect device reliability.
2. With an ICS approved pullable crystal.
Pullable Crystal Specifications:
Correlation (load) Capacitance
C0/C1
ESR
Operating Temperature
Initial Accuracy
Temperature plus Aging Stability
14 pF
250 max
35
Ω
max
0 to 70 °C or -40 to 85 °C
±20 ppm
±50 ppm
MDS 3732-08 C
3
Revision 091201
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408) 295-9800 tel • (408) 295-9818 fax • www.icst.com
MK3732-08
ADSL Clock Source
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC Publication No. 95.)
20 pin SSOP
Inches
Symbol Min
Max
A
0.053 0.069
A1
0.004 0.010
b
0.008 0.012
c
0.007 0.010
D
0.337 0.344
e
.025 BSC
E
0.228 0.244
E1
0.150 0.157
L
0.016 0.050
Millimeters
Min
Max
1.35
1.75
0.10
0.25
0.20
0.30
0.19
0.25
8.56
8.74
0.635 BSC
5.79
6.20
3.81
3.99
0.41
1.27
E1
E
INDEX
AREA
1
2
D
A1
e
b
c
L
A
Ordering Information
Part/Order Number
MK3732-08R
MK3732-08RTR
MK3732-08RI
MK3732-08RITR
Marking
MK3732-08R
MK3732-08R
MK3732-08RI
MK3732-08RI
Shipping packaging
tubes
tape and reel
tubes
tape and reel
Package
20 pin SSOP
20 pin SSOP
20 pin SSOP
20 pin SSOP
Temperature
0 to 70 °C
0 to 70 °C
-40 to 85 °C
-40 to 85 °C
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems,
Incorporated (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third
parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in
normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or
other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the
right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life
support devices or critical medical instruments.
MDS 3732-08 C
4
Revision 091201
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408) 295-9800 tel • (408) 295-9818 fax • www.icst.com
京公网安备 11010802033920号
EEWORLD
