EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TI2SA4082

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-TI2SA4082 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,

PH1-TI2SA4082 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1558 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
The serial port TTL level is abnormal
Platform: s3c2440 + wince5.0 UART1 is connected to the UART of the microcontroller on the same PCB board, 3-wire system, TTL, both powered by 3.3v. Phenomenon: (1) In CE, the serial port debugger send...
wuxianwwwwww Embedded System
Wire length measurement issues in different versions of Altium software
I used Altium Designer 10 and 14 to measure the line length of the same data bus on the same PCB board, and found that there was a big difference, and the difference could not be corrected. Which vers...
Evil93 PCB Design
Looking for the PCB package of fs75r06ke3 (IGBT module)!
I want the PCB package of fs75r06ke3 (IGBT module)! Thank you!...
yhye2world PCB Design
How to eliminate the ripple of PWM affecting power supply in LED boost circuit
[backcolor=rgb(239, 245, 249)] As shown in Figure 1, this is my LED driver circuit, powered by a 5V switching power supply. When I use 50% PWM (100Hz) to control the IC, it will have the effect shown ...
麻袋 Power technology
Operational Amplifier Model Introduction
A supervision introduction to general op amp models...
fighting Analog electronics
Three designs of constant current circuit
As a hardware RD engineer, I believe you are familiar with constant current circuits. This article introduces the schematics of three constant current circuits. Transistor constant current circuitTran...
可乐zzZ Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2668  880  2252  557  1922  54  18  46  12  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号