Maximum TX Input Power into 50Ω Load for 11a/n/ac (No Damage)
Moisture Sensitivity
Rating
-0.5 to +5.4
-0.5 to 5
500
-40 to +85
-40 to +150
+12
MSL1
Unit
V
DC
V
DC
mA
ºC
ºC
dBm
Caution!
ESD sensitive device.
RFMD Green: RoHS status based on EU
Directive 2011/65/EU (at time of this
document revision), halogen free per IEC
61249-2-21, < 1000ppm each of
antimony trioxide in polymeric materials
and red phosphorus as a flame retardant,
and <2% antimony in solder.
Exceeding any one or a combination of the Absolute
Maximum Rating conditions may cause permanent
damage to the device. Extended application of Absolute
Maximum Rating conditions to the device may reduce
device reliability. Specified typical performance or
functional operation of the device under Absolute
Maximum Rating conditions is not implied.
Nominal Operating Parameters
Specification
Parameter
Min
Compliance
Operating Frequency
Extended Frequency
Operating Temperature
Power Supply V
CC
Switch Control Voltage - SW_CTL High
Switch Control Voltage - SW_CTL Low
PA Enable – High
PA Enable - Low
5.15
4.9
-30
3
2.75
2.75
5.85
5.15
+85
4.2
4.2
0.4
4.2
0.4
GHz
GHz
ºC
V
V
V
V
V
Unit
Typ
Max
Condition
802.11a, 802.11n, 802.11ac
Functional with reduced performance
3.6
2.9
0.1
2.9
0.1
TX switch On at high control voltage
RX switch On with low control voltage
PA in “On” state
PA in “Off” state, Do not leave floating
Transmit (TX-ANT) Mode
Gain (5.15 to 5.85GHz)
20MHz Output Power*
11ac 20MHz Dynamic EVM
40MHz Output Power*
11ac 40MHz Dynamic EVM
80MHz Output Power*
11ac 80MHz Dynamic EVM
80MHz Output Power*
11ac 80MHz Dynamic EVM
Spectral Mask 20MHz Output Power*
Spectral Mask 40MHz Output Power*
Spectral Mask 80MHz Output Power*
Operating Current - Nominal
Second Harmonic
Third Harmonic
25.5
18.5
29
19
-33
2.2
18
-36
1.5
17
-36
1.5
13.5
-40
1.0
22
21
20
270
dB
dBm
dB
%
dBm
dB
%
dBm
dB
%
dBm
dB
%
dBm
dBm
dBm
mA
dBm/MHz
dBm/MHz
T= +25C°; V
CC
=3.6V; SW_CTL = High; PA_EN = High;
LNA_EN = Low; Unless otherwise noted
802.11ac HT20 MCS7
-30
3.2
-35
1.8
-35
1.8
17.5
802.11ac VHT40 MCS9
16.5
802.11ac VHT80 MCS9
802.11ac VHT80 MCS9
330
-40
-38
802.11ac HT20 with 3dB margin
802.11ac VHT40 with 3dB margin
802.11ac VHT80 with 3dB margin
P
OUT
= 19dBm
Fundamental frequency is between 4900 and 5850MHz; RF
P
OUT
= 19dBm; Measured in 1MHz resolution bandwidth (FCC
limit max = -30dBm)
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS130923
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
2 of 9
RFFM8506
Specification
Parameter
Min
Transmit (TX-ANT) Mode
(continued)
PA Selectivity/Out of Band Gain
30 to 2900MHz
3600 to 4400MHz
7250 to 7750MHz
TX Port Return Loss
ANT Port Return Loss
Noise Figure
-6
20
16
12
15
6
dB
dB
dB
dB
dB
dB
Unit
Typ
Max
Condition
T= +25C°; V
CC
=3.6V; SW_CTL = High; PA_EN = High;
LNA_EN = Low; Unless otherwise noted
10
12
Receive (ANT-RX) LNA On
Gain
Noise Figure
Rx Port Return Loss
ANT Port Return Loss
Input IP2
Input IP3
Current Consumption
LNA_EN Control Current
LNA Turn On Time
10
8
8
5
12
2.5
10
10
50
6
12
75
dB
dB
dB
dB
dBm
dBm
mA
μA
nS
T= +25C°; V
CC
=3.6V; SW_CTL = Low; PA_EN = Low;
LNA_EN = High; Unless otherwise noted
120
300
Receive (ANT-RX) Bypass Mode
Insertion Loss
Noise Figure
RX Port Return Loss
ANT Port Return Loss
ANT-RX Isolation
Input IP3
LNA Bypass Current
3.5
3.5
10
10
20
15
dB
dB
dB
dB
dB
dBm
μA
μA
μA
μA
μA
nS
nS
nS
V
V
VSWR
T= +25C°; V
CC
=3.6V; SW_CTL = Low; PA_EN = Low;
LNA_EN = Low; Unless otherwise noted
8
8
26
18
PA_EN = High; Maximum power
General Specifications
Switch Control Current – High - Each
Line
Switch Control Current – Low - Each
Line
PA_EN Current
Leakage Current – Nominal
Switching Speed
PA Turn-On Time from PA_EN edge
PA Turn-Off Time from PA_EN edge
ESD – Human Body Model
1000
ESD – Charge Device Model
1000
Ruggedness
*For 4900MHz to 5150MHz, P
OUT
is reduced by 1dB
2
0.1
30
15
200
300
300
Do not leave floating
RF Off; PA_EN = Low; SW_CTL = Low
Output stable within 90% of final gain
Output stable within 90% of final gain
EIA/JESD22-114A all pins
EIA/JESD22-101C all pins
With nominal input power
10:1
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS130923
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
3 of 9
RFFM8506
Switch Control Logic Truth Table
Operating Mode
802.11a/n/ac TX
802.11a/n/ac RX Gain
802.11a/n/ac RX Bypass
Note: All Logic Low pins ≤ 0.4V
PA_EN
High
Low
Low
SW_CTL
High
Low
Low
LNA_EN
Low
High
Low
Timing Diagram
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS130923
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
4 of 9
RFFM8506
Timing Sequence Notes
802.11a/n/ac Transmit Biasing Instructions
1. Connect the FEM to a signal generator at the input and a spectrum analyzer at the output. Terminate
unused ports with 50 Ohms
2. Set the power supply voltage to 3.0-4.2V first with PA_EN < 0.4V. Leakage current will be <15uA typical.
3. Refer to switch operational truth table to set the control lines at the proper levels for WiFi TX. All OFF
voltages must be < 0.4V (do not leave floating.)
4. Turn on PA_EN with levels indicated in the datasheet. PA_EN controls the current drawn by the
802.11a/n/ac power amplifier and the current should quickly rise to ~200mA +/- 20mA for a typical part but
the actual operating current will be based on the output power desired. Be extremely careful not to exceed
5.0V on the PA_EN pin or the part may exceed device current limits.
802.11a/n/ac Transmit Turn ON Sequence (See Transmit Timing Diagram)
1. Turn ON power supply.
2. Turn ON PA_EN.
3. Turn ON SW_CTL.
4. Apply RF.
802.11a/n/ac Transmit Turn OFF Sequence
1. Turn OFF RF.
2. Turn OFF SW_CTL.
3. Turn OFF PA_EN.
4. Turn OFF power supply.
802.11a/n/ac Receive
1. To receive WiFi set the switch control lines per the truth table.
2. Antenna port is input and RX port is output for this test.
3. Follow Timing Diagram for biasing instructions.
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS130923
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
There is a piece of board with an empty space on it, about 5CM*5CM. I happen to have a small board inside the 5CM*5CM area. I want to dig it out and make other small boards. How should I cut it in the...
I am using LM3S6965 now. I want to ask if the serial port of this device can be directly connected to the serial port of 51 microcontroller? Can RX connect to TX and TX connect to RX? I am trying, but...
Has anyone calculated the OFS of the ADC of KW41Z? Please help me calculate how much OFS should be set to subtract 179 from the AD result? The number of digits of the AD result is 12. In the instructi...
I am currently working on a stepper motor subdivision drive circuit and would like to find a mature solution. Could you please recommend some circuits or books? Thank you....
Hello everyone, I have a question. This example illustrates how to configure the EMI. { u8 data; ... // Initialize the EMI bank 1: enable, 2 wait states, 16-bit wide external EMI_Config(1, EMI_ENABLE ...
Designers use PSpice primarily to simulate analog circuits. However, it can also be used to simulate digital filters. The main components in a digital filter are delay elements, adders, and multipl...[Details]
The U.S. Food and Drug Administration (FDA) points out that home health care is the fastest growing area in the medical device industry. Driven by the increase in average life expectancy, the increasi...[Details]
Ultrasound systems are among the most sophisticated and complex signal processing instruments in widespread use today. Like any complex instrument, there are many trade-offs to be made in implement...[Details]
Medical and industrial applications often require isolation voltages of 2500Vac or higher for patient and equipment operator safety. The isolation barrier must not only transmit power to the sensin...[Details]
With the advancement of computer technology, the development of image processing and pattern recognition methods, fingerprint processing technology has become more mature and has been widely used i...[Details]
The particularity of portable medical devices determines that they should be user-friendly, must work in a sterile environment, and occupy little space and consume low energy.
At the same time, por...[Details]
The hardware circuit principle is shown in Figure 1. In the specific design, each part should consider the anti-interference problem to minimize the impact of interference on the performance of the...[Details]
With the rapid development of computer technology, embedded image systems are widely used in office equipment, manufacturing and process design, medical, monitoring, sanitary equipment, transportat...[Details]
Over the past 15 to 20 years, automotive power MOSFETs have evolved from an initial technical topic to a thriving commercial sector. Power MOSFETs were chosen because they can withstand transient ...[Details]
As microcontrollers become less expensive and more powerful, electrical designers are finding it more cost-effective to use multiple small controllers in both single-board and multi-board systems. ...[Details]
introduction
The data detected by various measuring instruments often need to be transferred to the PC for data processing and archiving, so as to make full use of the rich hardware and softwa...[Details]
Overview
Currently, many portable consumer electronic products, such as mobile phones, PDAs, MP3 players, and notebooks, are equipped with display screens. Although the type and size of the di...[Details]
At present, the IEEE802.11 wireless LAN standard is widely used in voice communication, wireless office and other fields, but it is still mainly limited to wireless communication on general platfor...[Details]
Fetal monitoring is an important means to ensure the safety of perinatal mothers and fetuses and achieve eugenics. Intelligent fetal monitoring is a monitoring method that analyzes the health stat...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communication technology since the advent of digital communications. Many new wir...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
