All temperatures refer to topside of the package, measured on the package body surface.
260°C Reflow Profile
W
&
W &
3°C/seconds max.
150°C
200°C
60-180 seconds
3°C/seconds max.
217°C
60-150 seconds
max 260°C
Time within 5°C of actual
Peak Temperature (tp)
Ramp-down Rate
6°C/seconds max.
20-40 seconds max.
W
&
W &
8 minutes max.
Average ramp-up rate (TL to TP)
Preheat - Temperature min Tsmin
- Temperature min Tsmax
- Time (min to max) (ts)
Tsmax to TL -Ramp-up Rate
Time maintained above - Temperature (TL)
- Time (TL)
Peak Temperature (Tp)
E
Time 25°C to Peak Temperature
Time maintained above
- Temperature (TL)
- Time (tL)
217°C
60-150 seconds
All temperatures refer to topside of the package, measured on the package body surface.
4 of 5
Ordering Information
EX - 401 0 - D A P - 108 0 - 10M0000000
Frequency
Frequency Control
20
Configuration
Thru-hole
Stability Code
Supply Voltage
508: ±50ppb
758: ±75ppb
107: ±100ppb
6: Fixed Frequency (+5 dBm)
7: Electrical Tuning (+5 dBm)
d
d
^
Z
Z
^
&
&
d
^
d
108 (+/-10ppb)
208 (+/-20ppb)
308 (+/-30ppb)
508 (+/-50ppb)
758 (+/-75ppb)
107 (+/-100ppb)
A: -55°C to +85°C E: -40°C to +85°C J: -20°C to +70°C P: 0°C to +50°C
10-20MHz
10-20MHz
10-50MHz
10-80MHz
10-100MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
Aging Table
Temperature Range and Stability Table
Notes:
Stability/Temperature A: -55°C to +85°C
E: -40°C to +85°C
J: -20°C to +70°C
1.
108
(+/-10ppb)
frequencies.
10-30MHz
2.
208 (+/-20ppb)
10-30MHz
10-30MHz
308 (+/-30ppb) 10-30MHz
10-30MHz
10-30MHz
10-30MHz
4.
Subject to technical modification.
Contact factory for availability.
P: 0°C to +50°C
For Additional Information, Please Contact
USA:
Vectron International
Europe:
Vectron International
Asia:
Vectron International
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
I am using MSP430 F5529, and I want to use P2.5 as input to detect a common emergency stop switch, which is normally set high and pulled low when pressed;I originally connected P2.5 to the 3.3V power ...
This part talks about external interrupts. Reading the introduction and understanding the program is the best way. External interrupts are the lowest priority interrupts of MSP430 and are maskable int...
Material name: "Initialization of I2C controller on MPC8548, reading and writing single bytes, continuous reading and writing of multiple bytes and other functions. Debugging passed" Thank you very mu...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
