L15 Incremental Optical Encoder
Mechanical Specifications
Shaft Diameter:
1/4 inch nominal
Shaft Loading:
Up to 5 pounds axial and 5 pounds radial
Shaft Runout:
0.002 T.I.R. at midpoint of shaft
Starting Torque at 25°C:
0.20 in-oz (max)
Bearings:
Sealed, instrument grade
Shaft Material:
416 stainless steel
Bearing Housing:
Aluminum with protective finish
Cover:
Drawn aluminum
Bearing Life:
1 X 10
9
revs (10,000 hrs at 1500 RPM)
Maximum RPM:
5,000 RPM nominal (see Frequency Response, below)
Moment of Inertia:
1.0 X 10
-4
oz-in-sec
2
Weight:
6 oz (max)
Output Format:
2 channels in quadrature, 1/2 cycle index gated with negative B channel
Cycles Per Shaft Turn:
24 to 40,640 (see Table 2 back page)
Supply Voltage:
5-28 VDC
Current Requirements:
100mA typical + output load 250mA (max), 150mA (max) with 28V/5
Voltage/Output:
28V/V: Line Driver, 5–28VDCin, Vout =Vin
28V/5: Line Driver, 5–28VDCin, Vout =5VDC
28V/OC: Open Collector, 5–28VDCin, OCout
Protection Level:
Reverse, overvoltage and output short circuit
Frequency Response:
100kHz (non-interpolated),Up to 1 MHz interpolated
Output Termination Pinouts:
see table on back page
Electrical Specifications
The L15 provides the industrial marketplace with a rugged high-
resolution encoder in a compact size 15 servo package. Engineered
with robust interpolative electronics, the L15 offers up to 40,640 cycles
per turn. Ideal for space or weight limited applications, these compact
encoders discount size without compromising performance.
The L15 encoder features 1/4-inch diameter stainless steel shaft and
can accommodate up to 5 pounds radial or axial load. The L15 encoder
package has field-proven ASIC electronics, sealed dual bearings and
BEI’s accurate code disk in an all metal housing to ensure ruggedness
and reliability.
The L15 Incremental Encoder is available with the
following certifications:
EN 55011 and EN 61000-6-2
Environmental Specifications
Enclosure Rating:
NEMA 3. (IP53)
Temperature:
Operating, 0º to 70º C; extended temperature testing available,
-40º to 85º ; storage, -40º to 90º C
Shock:
50 G’s for 11 msec duration (1/2 Sine)
Vibration:
20 to 2000 Hz @ 20 g’s
Humidity:
98% RH non-condensing
NOTES & TABLES:
All notes and tables referred to in the text can be found on
the back of this page.
L15 Incremental Ordering Options
L15
TYPE
:
L = Light Duty
15 = 1.5 inch
diameter
HOuSINg:
M = Standard
for assistance call 800-350-2727
Use this diagram, working from left to right to construct your model number (example: L15M-F25-256-ABZC-28V/V-SC18)
M
CHANNELS:
ABZ
ABZC
SPECIAL
FEATuRES:
S= Special
features specified
on purchase order
(consult factory)
FACE MOuNT:
F25 = Standard
RESOLuTION
NuMBER OF CYCLES:
1 to 2540
See Table 2, back page
See Figure 1,
back page
INTERPOLATION:
T2, T3, T4, T5, T8,
T10, T12, T16
VOLTAgE/OuTPuT:
28V/V = 5-28V
in/out
28V/OC = 5-28V
in
/
OC
out
See note 5
See note 6
OuTPuT
TERMINATION:
SCS = Shielded, Jacketed Cable with Cable
Gland Seal and Cable length in inches
(i.e. SCS18 = Pigtail 18 inches)
See table 1, back page
tel: 805-968-0782 /800-350-2727 | fax: 805-968-3154 / 800-960-2726
7230 Hollister ave., Goleta, ca 93117-2807 |
www.beisensors.com
specification no. 02069 rev.08-11
These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
L15 Incremental Optical Encoder
Notes
1.
Mounting is usually done either using the D-style square flange mount, E- or G-style servo
mounts, or one of the standard face mounts, F1 for example. Consult factory for additional
face mount options.
2.The
shaft seal is recommended in virtually all installations. The most common exceptions
are applications requiring a very low starting torque or those requiring operation at both high
temperature and high speed.
3.
Non-standard index widths and multiple indices are available by special order.
Consult factory.
4.
Complementary outputs are recommended for use with line driver type (source/sink)
outputs. When used with differential receivers, this combination provides a high degree
of noise immunity.
5. Output IC’s:
Output IC’s are available as either Line Driver (LD) or NPN Open Collector
(OC) types. Open Collectors require pull-up resistors, resulting in higher output source imped-
ance (sink impedance is similar to that of line drivers). In general, use of a Line Driver style
output is recommended. Line Drivers source or sink current and their lower impedance mean
better noise immunity and faster switching times.
Warning:
Do not connect any line driver
outputs directly to circuit common/OV, which may damage the driver. Unused outputs should
be isolated and left floating. Our applications specialists would be pleased to discuss your
system requirements and the compatibility of your receiving electronics with Line Driver
type outputs.
28V/V:
Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC
+/- 5% standard (Note: V
out
= V
in
). This driver is TTL compatible when used with 5 volt sup-
ply. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs
are short circuit protected for one minute. Supply current is 120 mA typical (plus load cur-
rent). This is the recommended replacement for 3904R and 7406R open collector outputs
with internal pullup resistors. It is also a direct replacement for any 4469, 88C30, 8830 or
26LS31 line driver.
28V/5:
Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/-
5% standard, internally regulated with 5V (TTL compatible) logic out. Supply lines are pro-
tected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected
for one minute. Supply current is 90 mA typical (plus load current).
Note:
Limit encoder load
to 2.5W max at ambient. Example at 12 VDC: 2.5W/(+12VDC minus +5VDC) = 357 mA total
allowed current. Consult factory for your specific requirements.
15V/V:
Multi-voltage Line Driver (4469*): 100 mA source/sink. Input voltage 5 to 15 VDC
+/- 5% standard (Note: V
out
= V
in
). TTL compatible when used with 5 volt supply. Supply
lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short
circuit protected for one minute. Supply current is 90 mA typical (plus load current). This is a
direct replacement for the 4469 Line Driver.
28V/OC:
NPN Open Collector (3904*, 7273*). Current sink of 80 mA max. Current sourced
by external pull- up resistor. Output can be pulled up to voltage other than supply voltage (30
V max). Input voltage 5 to 28 VDC
+
/- 5% standard. Supply current is 120 mA typical. This
replaces prior IC’s with designations of 3904, 7406, 3302, 681 and 689.
5V/OCR, 15V/OCR, 24V/OCR:
Open Collector (3904R*, 7406R*, 7273R*): Current sink of
70 mA max. Includes internal pull-ups sized at approximately 100 ohms/volt. Max current
source is 10 mA. Supply current is 100 mA typical, 120 mA with internal pull-ups. The 5V/
OCR, 15V/OCR and 24V/OCR are often replaced by the 28V/V in system upgrades.
6.
Special –S at the end of the model number is used to define a variety of non-standard
features such as special shaft lengths, voltage options, or special testing. Please consult the
factory to discuss your special requirements.
7.
Higher frequency response may be available. Please consult with the factory.
8.
Extended temperature ratings are available in the following ranges: -40 to 70°C, -40 to
85°C, –20 to 105°C and –40 to 105°C depending on the particular model. Some models
can operate down to -55°C. Extended temperature ranges can affect other performance fac-
tors. Consult with factory for more specific information.
* Products manufactured prior to April 2007 used the line driver IC number instead of voltage output in model number.
Tables
Table 1–
Output Functions
COLOR
RED
BLK
YEL
WHT/YEL
BLU
WHT/BLU
ORN
WHT/ORN
BARE
FUNCTION
+V (SUPPLY)
0 V (COMMON)
A
A
B
B
Z
Z
SHIELD DRAIN
Table 2–
L15 Disc Resolutions
(Other resolutions and interpolation
options available—consult factory.)
24 50 100 200 256
300
360 400
500
512 625 900 1000
1024 1200 1250 1440
1800 2000 2048 2500
2540
Figure 1
Output Waveforms
Dimensions
TOLERANCES: .XX=±0.02, .XXX=±0.005
tel: 805-968-0782 /800-350-2727 | fax: 805-968-3154 / 800-960-2726 | 7230 Hollister ave., Goleta, ca 93117-2807
www.beisensors.com
MCU
京公网安备 11010802033920号
EEWORLD
