ohahaha

Powerline communication modules for street lighting

STEVAL-IHP007V1

Overview

The STEVAL-IHP007V1 evaluation board is a power line communication module addition to the STEVAL-ILH007V1 HID ballast module. It provides functions for the management of street lighting network architecture in the CENELEC A-B-D bands.

The module is based on an STM32F103CBT7 ARM Cortex-M3 microcontroller and an ST7580 PSK narrow band power line modem with up to 28.8 kbps data rate. The embedded MCU can be easily replaced with an equivalent 48-pin MCU from the STM32F0, STM32F2, STM32F3 families with a few changes.
The module is designed to work with the STEVAL-ILH007V1 HID module, but can be associated with other lighting driver boards with a standard serial communication port.
Note that this board only functions in a network with an EVALKITST7580-1 board designated as the master; this is achieved via UART commands.

Main features

SM6T15CA: Transil 600 W TVS diode
SMAJ5.0CA-TR: Transil 400 W TVS diode
ST7580: FSK, PSK multi-mode power line networking system-on-chip
STM32F103CBT7: STM32 ARM-based 32-bit MCU
STPS1L30: low drop power Schottky rectifier 1 A, 30 V, 0.3 V
STTH1L06A: Turbo 2 ultrafast high voltage rectifier
RoHS compliant

Design Files

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.

Hot

Technical Resources More

Search Datasheet?

Supported by EEWorld Datasheet

Technical Videos More

Forum More

Update:2025-06-23 04:00:38

12864
Looking for a fm12864 serial reading program or dot drawing circle program
CCS6 Problem importing controlsuite routine
When importing a project, the software prompts that an unrecognized product of type'com.ti.rtsc.XDAIS' is required by project ' Example F2802xGpio Toggle' -please install at least one product of this
[ST Motor Evaluation] 4. Self-made tasks, horizontal comparison of ST and TI motor control
At this point, we can try to compare the electronic control of ST and TI. ST uses the NUCLEO+IHM002 of this event, and TI uses the classic 28069+DRV8301. Both are boards for beginners, so I think they
AUX launches TVS devices for harsh environments
[8-|][A][:@]AUX launches TVS devices for harsh environments[ Print ][ Return ]AVX has introduced a series of radiation-hardened transient voltage suppressors (TVS) using multilayer varistors and zinc
IAR MSP430 "the stack pointer for stack is outside" error handling
[i=s]This post was last edited by Aguilera on 2020-2-9 21:38[/i]Modify the debugger, error:The stack pointer for stack'stack' (currently Memory:0x252) is outside the stack range (Memory:02B0 toMemory:
How to allow two components to overlap without a warning (green)
When drawing PCB, several connectors need to be arranged closely side by side, as shown below, and a warning prompt appears [align=center][/align] I have encountered this problem before. At that time,

Datasheet More

Circuits More