CN0276

High Performance, 10-Bit to 16-Bit Resolver-to-Digital Converter

Schematic PCB

CN0281

Using ADuC7060/ADuC7061 precision analog microcontroller to build a thermocouple temperature sensor with cold junction compensation based on automotive SENT interface

Schematic PCB

CN0234

Single-supply, micropower toxic gas detector using electrochemical sensors

Schematic PCB

CN0280

Integrated isolated power supply, powerful fully isolated current sensing circuit for solar photovoltaic converters

Schematic PCB

CN0183

Precision, 16-bit bipolar output voltage source using +12V to ±5V supplies

Schematic PCB

MAXREFDES1238: Scalable, single-input, 6-output, power supply solution for Version ACAP platform

In this design a single 12V input supplies a circuit which outputs 6 separate rails ranging from 500mW to 130W. The design is specified to meet the XILINX Versal ACAP AI Core Series UC1/3 requirements. The design layout is also optimized for the Versal ACAP IC.

Schematic PCB

KPower supply design for Kintex Ultrascale FPGA: ultra-quiet, 1.8V, 1A

This reference design provides a power-supply circuit with an input voltage of 3.3V, an output voltage of 1.8V, and an output current of 1A using the MAX8869 low-dropout linear regulator. The circuit was developed to power a MGTVCCAUX rail on a Xilinx® Kintex® Ultrascale™ FPGA. Included in this reference design are a schematic and a bill of materials.

Schematic PCB

Power supply design for Kintex Ultrascale FPGA: PMBus compatible, strictly regulated, 1.80V, 2A

This reference design provides a power-supply circuit with an input voltage of 10.8V to 13.2V, an output voltage of 1.80V, and an output current of 2A using the MAX15303 InTune™ Point-of-Load (PoL) Controller. The circuit was developed to power a VCC1V8 rail on a Xilinx® Kintex® Ultrascale™ FPGA. Included in this reference design are a schematic, applications information, and a bill of materials.

Schematic PCB

MAXREFDES108#: Non-isolated 12V/1A PoE powered device power supply

This document details the MAXREFDES108# subsystem reference design, a 36V to 57V input, 12V output, step down non-isolated power supply capable of 12W. Design files and test results are included. Hardware is available for purchase.

MAXREFDES1185: 3.5W, 24V offline flyback converter using MAX17595

The MAX17595 is a peak-current-mode controller for designing wide input-voltage flyback regulators.

MAXREFDES1260: Li-ion battery charger and monitoring system with 3A USB-C input

The requirements for higher quality and performance in digital SLR cameras, DSC, and other 2S Li+ battery electronic equipment is increasing.

Schematic PCB

MAXREFDES1219: 1-cell USB charger and fuel gauge

The MAXREFDES1219 is an integrated smart solution for the 1-cell Li+ battery pack that provides a linear charger

Schematic PCB

MAXREFDES1277: 48V data acquisition system with integrated current sense amplifier for two-wheeler battery management applications

The MAXREFDES1277 reference design enables quick evaluation of the MAX17852/53 for 48V two-Wheeler battery management applications (BMS)

Schematic PCB

CN0209

Fully programmable universal analog front end for process control applications

Schematic PCB

Kintex-7 series power module

This reference design enables a complete power-supply solution for powering Xilinx® Kintex®-7 series field-programmable gate array (FPGA) using Maxim's power-supply solutions.

CN0218

500 V common mode voltage and current monitor

Schematic PCB

CN0241

High-side current sensing with input overvoltage protection

Schematic PCB

MAXREFDES48#: 24V to 12V, 40W isolated power supply with EFD20 core transformer

The MAXREFDES48# reference design is a high-efficiency, high-precision, isolated DC-DC forward converter with an active clamp, current-mode PWM controller. The converter accepts 18V to 36V DC input and delivers output current up to 3.5A at 12V . Test results and hardware files provide complete documentation for the design. The board is also available for purchase.

Schematic PCB

CN0196

Isolated full-bridge driver circuit

Schematic PCB

MAXREFDES1054: Non-isolated, single output, synchronous Buck, step-down DC-DC converter

The MAX17506 high-efficiency, high-voltage, synchronous step-down DC-DC converter with integrated high-side MOSFET operates over a 4.5V to 60V input. The converter can deliver up to 5A and generates output voltages from 0.9V up to 0.9 x VIN. The feedback (FB) voltage is accurate to within ±1.4% over -40°C to +125°C. The MAX17506 uses peak current-mode control and can be operated in the pulse-width modulation (PWM), pulse-frequency modulation (PFM), and discontinuous conduction mode (DCM) control schemes.