OM13323: NVT2006PW Demonstration Board

OM13489: Universal 16-bit general-purpose IO daughter board for Fm+ development board

KIT35XS3500EVBE: Evaluation Kit - MC35XS3500, Smart Rear Corner Light Switch

FRDM-CD1030EVM: FRDM-CD1030EVM Switch Detection Interface Evaluation Kit Quick Start

Schematic PCB

KITUSBSPIEVME: Evaluation Kit-USB-SPI Interface, MC68HC908JW32

KIT33978EKEVB: Evaluation Kit - MC33978, 22-channel switch detection

KIT33903BD5EVBE: Evaluation Kit - MC33903BD5, 2nd Generation SBC with CAN and LIN

KIT33662LEFEVBE: Evaluation Kit - MC33662L, LIN2.1/SAEJ2602-2, LIN Physical Layer

KIT33662JEFEVBE: Evaluation Kit - MC33662J, LIN2.1/SAEJ2602-2, LIN Physical Layer

KIT33905D5EKEVBE: Evaluation Kit - 33905D5, 2nd Generation SBC with CAN and LIN

KIT33905BD3EVBE: Evaluation Kit - 33905D3, 2nd Generation SBC with CAN and LIN

KIT33972AEWEVBE: Evaluation Kit-33972, MSDI with Wake Suppression

SJA1105Q-EVB: Ethernet switch and PHY evaluation board.

FRDMCD1020EVM: CD1020 evaluation board - 22-channel switch detection interface

The FRDMCD1020EVM Evaluation Board (EVB) features the CD1020, a 22-channel switch detection interface with a programmable wetting current.

Schematic PCB

OM14500-TJA1102: Evaluation Board, TJA1102HN 100BASE-T1 Automotive Ethernet PHY

OM13529UL: PCAL6524/(EV-VFBGA36)(S500)Fm+ I2C 24-bit GPIO Demonstration Board

ADTJA1101-RMII: TJA1101 Automotive Ethernet Adapter for S32K148EVB and i.MX8

230V, 3.5kW PFC reference design with greater than 98% efficiency, BOM and size optimization

TIDA-00779 is a 3.5kw affordable power factor regulator converter designed for room air conditioners and other large appliances. This reference design is a continuous conduction mode (CCM) boost converter and is implemented using the TI UCC28180 PFC controller and all the necessary built-in protection mechanisms that come with it. The hardware design has been tested and passed IEC61000 surge and EFT test requirements for household appliances.

Schematic PCB

Universal input 3.3V, 12V, 36V, 200W continuous PSU reference design for Class D amplifiers

This power module generates all the voltages required to power the Class D audio amplifier. The main output voltage is 36V, which provides 200W of continuous power and 540W of peak power. The first stage is a power factor correction boost. The flyback converter provides 12V on the primary side and 12V (300mA) and 3.3V (200mA) on the secondary side. Using a hardware switch and remote input, the converter can enter standby mode: in this state, the 36V output is disabled and 12V, 3.3V are "always on". In this way, the standby power can be reduced to 150mW (115Vac) and 270mW (230Vac). A second digital input switches the main input voltage from 36V to 18V, allowing it to enter a low-current consumption mode when the audio amplifier requires less power.

Schematic PCB

Tiny 2A Power Supply with LMZ20502 Nano Module - Reference Design

The PMP10595 reference design is a miniature 1.8V 2A output power supply using the SIMPLE SWITCHER® LMZ20502 micro module. This reference design leverages the LMZ20502's tiny package and high level of integration to achieve a small solution size of approximately 5mm x 6mm (30 mm2). This design has an input voltage range of 2.7V to 5.5V and provides an output of up to 2A. On the reference board, the LMZ20502 is set to automatic mode to achieve high efficiency at light load and full load.

Schematic PCB