syzygy-epc901: SYZYGY and EPC901 CCD + 50MSps ADC

The EPC901 is a 1024x1 CCD sensor capable of providing 50MHz pixel output. It outputs analog voltage from the CCD element. The author paired it with a 50MSps ADC on a SYZYGY board. The datasheet says it can run up to 50k fps. External I/O is provided via optocouplers to facilitate connection to external trigger sources such as motion controllers. This board will assist in conducting experiments on the new PnP platform. Objects can be moved through the line scanner to capture the position of the photo.​

Schematic PCB

OM13530: SA6x4AHR Evaluation Demonstration Board

Electric vehicle power inverter control reference platform

NXP's ASIL-D automotive system platform is a reference design that enables high-voltage power inverter control to drive electric vehicle traction motors and DC-DC converters.

IMX6SLEVK: i.MX 6SoloLite Evaluation Kit

NXPProvides highly flexible, market-ready development tools in an evaluation kit based on the i.MX 6SoloLite applications processor.

Schematic PCB

Use of MAX4090 with reconstruction filter

In most video applications, the video signal generated from the DAC requires a reconstruction filter to smooth out the signal and attenuate the sampling aliases. The MAX4090 is a direct, DC-coupled output driver, which can be used after the reconstruction filter to drive the video signal. The driving load from the video DAC can be varied from 75Ω to 300Ω. A low input impedance (< 100Ω) is required by the MAX4090 in normal operation, special care must be taken when a reconstruction filter is used in front of the MAX4090.

FPGA Power Solutions

Complete power solution for FPGAs

CN0183

Precision, 16-bit bipolar output voltage source using +12V to ±5V supplies

Schematic PCB

Smart and cool music flower-shaped lamp

Renesas’ flower reference design showcases a diverse portfolio of products for broad market applications. From power management to precision analog and specialty ICs, we've got you covered for your designs.

Schematic PCB

Create an audio preamplifier with an attenuator using the DS1802 push-button digital potentiometer

This application note discusses how to best bias the AC signal to within the DC supply range and how to use digital potentiometers in circuits designed for mechanical potentiometers. This understanding is crucial to effectively using the DS1802 in a pushbutton-controlled audio preamplifier circuit.

MAXREFDES1238: Scalable, single-input, 6-output, power supply solution for Version ACAP platform

In this design a single 12V input supplies a circuit which outputs 6 separate rails ranging from 500mW to 130W. The design is specified to meet the XILINX Versal ACAP AI Core Series UC1/3 requirements. The design layout is also optimized for the Versal ACAP IC.

Schematic PCB

TJBot, a DIY cardboard robot open sourced by IBM

Maker Kits are a set of DIY open source templates for building things using IBM AI services in fun and easy ways. IBM TJBot is the first maker kit in the series. You can 3D print or laser cut the robot's body and then bring it to life using the resources provided by IBM! Additionally, you can unleash your creativity and create new recipes, using any of the available IBM AI services to bring TJBot to life! TJBot only works with Raspberry Pi.

Schematic PCB

The early mobile phone system PalmOS was ported to Raspberry Pi RP2040

Schematic PCB

Reading pen

Use a reading pen with a Renesas Electronics RL78/G14 microcontroller, ISL80505 single-output low-dropout linear regulator (LDO), and ISL6294 high-input voltage charger to read the code printed on the paper and play the corresponding Audio.

SimpleLink™ ZigBee® Network Range Extender Reference Design

ZigBee applications such as home and industrial automation, lighting, metering and sensor networks may require longer RF transmission range and higher sensitivity than the standalone CC2530. TI's new SimpleLink CC2530-CC2592 reference design pairs the cost-effective SimpleLink ZigBee CC2530 wireless MCU with the SimpleLink CC2592 range extender to improve receiver sensitivity by 2-3 dB and increase the total link budget to 120 dB, significantly improving Coverage of each node in the ZigBee network.

Schematic PCB

OM13790 Host and Dock: USB Type-C Shield Board Gen 2 with DisplayPort Alt Mode

NXP is launching a Generation 2 USB Type-C Shield with display port alt mode support! The NXP Generation 2 USB Type-C shield works with the MCUXpresso SDK and USB Power Delivery stack to allow you to connect USB Type-C Connectors to select Kinetis®, LPC and i.MX RT development platforms.

Schematic PCB

QN9080SIP-DK: Highly scalable QN9080SIP application development platform

QN9080SIP-DK is a development kit supported by the QN9080-001-M17 module, supporting Bluetooth 5 and NFC.

Schematic PCB

Reverse Power Supply - Eight Input Single Output Reference Design

This reference design is a power supply solution for reverse powered telecom applications. Up to 8 isolated inputs provide a universal output; the load is shared equally among all active converters.

Schematic PCB

KPower supply design for Kintex Ultrascale FPGA: ultra-quiet, 1.8V, 1A

This reference design provides a power-supply circuit with an input voltage of 3.3V, an output voltage of 1.8V, and an output current of 1A using the MAX8869 low-dropout linear regulator. The circuit was developed to power a MGTVCCAUX rail on a Xilinx® Kintex® Ultrascale™ FPGA. Included in this reference design are a schematic and a bill of materials.

Schematic PCB

Wi-Fi smart power strip

The Wi-Fi smart power strip using RL78/G13 microcontroller and ISL85003 regulator can remotely control the opening and closing of each power socket through Wi-Fi.

Computer vision tool GluonCV: recognition, detection, segmentation, pose

CluonCV provides an implementation of state-of-the-art (SOTA) deep learning models in computer vision. It is designed for engineers, researchers and students to quickly prototype products and research ideas based on these models.

Schematic PCB