EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

PN5130/D26Z-J14Z

Description
UHF BAND, Si, NPN, RF SMALL SIGNAL TRANSISTOR, PLASTIC PACKAGE-3
CategoryDiscrete semiconductor    The transistor   
File Size132KB,4 Pages
ManufacturerTexas Instruments
Websitehttp://www.ti.com.cn/
Stay tuned Parametric

PN5130/D26Z-J14Z Overview

UHF BAND, Si, NPN, RF SMALL SIGNAL TRANSISTOR, PLASTIC PACKAGE-3

PN5130/D26Z-J14Z Parametric

Parameter NameAttribute value
MakerTexas Instruments
package instructionCYLINDRICAL, O-PBCY-T3
Reach Compliance Codeunknown
ECCN codeEAR99
Collector-based maximum capacity1.7 pF
Collector-emitter maximum voltage12 V
ConfigurationSINGLE
Minimum DC current gain (hFE)15
highest frequency bandULTRA HIGH FREQUENCY BAND
JESD-30 codeO-PBCY-T3
Number of components1
Number of terminals3
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formCYLINDRICAL
Polarity/channel typeNPN
Minimum power gain (Gp)14 dB
Certification statusNot Qualified
surface mountNO
Terminal formTHROUGH-HOLE
Terminal locationBOTTOM
transistor applicationsAMPLIFIER
Transistor component materialsSILICON
Nominal transition frequency (fT)450 MHz
VCEsat-Max0.6 V
Sequential logic test question!!
I want to know if there is a chip, but I don't know the model and purpose, nor the pin arrangement, is there any way to test its logic function? Or if I know the pin arrangement, is there any way to t...
beck21 Embedded System
How to filter out 50HZ power frequency interference introduced by active filtering
I need to amplify a sine wave signal of about 1mV to collect its frequency. I use AD620+active bandpass filter+OP07 amplification for signal acquisition. At present, after the second-level active filt...
天天1 Analog electronics
Is it the inverter or the integrator circuit?
As shown The input Uin of the op amp is obtained from the -380VDC bus through resistor voltage division to obtain -3.5VDC Is the op amp in the figure a simple inverting 1:1 amplifier circuit, or is it...
shaorc Analog electronics
How to configure uclinux to automatically obtain an ip after arm is powered on?
How to configure uclinux to let arm automatically get ip after power on? My development board is S3C44B0. I heard that uclinux supports dhcp. 1. What should I choose when compiling uclinux 2.4 kernel ...
wawj1819 Linux and Android
Can first-tier devices do the job?
Previously, the sensor head was made by Honeywell combined with first-line devices. The SHT21 may be smaller in size. The I2C interface direct cable transmission requires signal preprocessing. Can fir...
bjwl_6338 DIY/Open Source Hardware
linux-2.6.34 kernel porting documentation [simple operation]
I just transplanted the kernel image file, put it on the development board and ran it for a while, and the system is running!!! Pictures speak louder than words...See the attached documentation for th...
37°男人 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1487  2008  1979  275  204  30  41  40  6  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号