stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
PERSONAL INJURY
•
The WDRR must be installed in accordance with the
requirements specified in this document in order to comply
with the specific Country Communication Agency
requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See
Section 3 as it requires choosing the correct Country Use
Code and thus allowable antenna and/or cable usage.
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
•
Pay attention to ESD discharge at dc-in port.
WARNING
WARNING
•
Korean Communication Commission does not allow this
equipment to be used for rescue service.
•
Anatel states that this device works as a secondary
function model. It may not be used as a protection device
against harmful interference. It cannot cause interference
with systems that are running as primary function.
WARNING
CAUTION
* Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
WARNING
•
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result in
death or serious injury.
RF EXPOSURE
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will be
printed on the Limitless™ input label). If the Limitless™
input is paired with older firmware (FW7170 or a lesser
number), the WDRR may exhibit delayed responses
under simultaneous operation.
Sensing and Productivity Solutions
Limitless™
WDRR Receiver
T
ABLE OF
C
ONTENTS
Issue 5
50063987
TABLE OF CONTENTS
............................................................................................................................................................ II
LIST OF FIGURES
.................................................................................................................................................................... VI
The screenshots of the IR2130 chip manual are as follows:The underlined part in the first picture says that the current op amp provides the current value of the tube through an external resistor. As I...
I need help from seniors: I use Atmel studio 6.2 development environment, the hardware board is SAM4E Xplained Pro, open the example project [EDBG I2C Information interface Demo], clean solution-->reb...
Prize-winning live broadcast: ST's PLC solutions in industrial automation. You are invited to watch at 10:00 am on May 26 (Wednesday)!Click here to registerLive broadcast time: 10:00-11:30 am, May 26,...
1. Both electromagnets and permanent magnets can attract things like steel and iron. Are the things they can attach to the same? Is there any substance that electromagnets cannot attract but permanent...
General DescriptionZS3003 and ZS3004 are the USB dedicated charging controller ICs, which are fully compatible with BC1.2 and other non-BC1.2 standards like YT/D1591-2009,Apple charging specification ...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
Power supply is often the most easily overlooked link in the circuit design process. In fact, as an excellent design, power supply design should be very important, which greatly affects the perfor...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
