• Distributes one clock input to one bank of five and one bank of
four outputs
• Separate output enable for each output bank
• Output Skew < 250ps
• Low jitter <200 ps cycle-to-cycle
• IDT23S09E-1 for Standard Drive
• IDT23S09E-1H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Spread spectrum compatible
• Available in SOIC and TSSOP packages
The IDT23S09E is a high-speed phase-lock loop (PLL) clock buffer,
designed to address high-speed clock distribution applications. The zero
delay is achieved by aligning the phase between the incoming clock and
the output clock, operable within the range of 10 to 200MHz.
The IDT23S09E is a 16-pin version of the IDT23S05E. The IDT23S09E
accepts one reference input, and drives two banks of four low skew clocks.
The -1H version of this device operates up to 200MHz frequency and has
higher drive than the -1 device. All parts have on-chip PLLs which lock
to an input clock on the REF pin. The PLL feedback is on-chip and is
obtained from the CLKOUT pad. In the absence of an input clock, the
IDT23S09E enters power down. In this mode, the device will draw less
than 12µA for Commercial Temperature range and less than 25µA for
Industrial temperature range, and the outputs are tri-stated.
The IDT23S09E is characterized for both Industrial and Commercial
operation.
FUNCTIONAL BLOCK DIAGRAM
16
CLKOUT
1
REF
PLL
2
CLKA1
3
CLKA2
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2006 Integrated Device Technology, Inc.
MAY 2010
DSC - 6399/11
IDT23S09E
3.3V ZERO DELAY CLOCK BUFFER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SOIC/ TSSOP
TOP VIEW
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Temperature
Operating
Temperature
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Input Clamp Current
Continuous Output Current
Continuous Current
Maximum Power Dissipation
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
±100
0.7
mA
mA
mA
W
Unit
V
V
V
CLKOUT
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
V
DD
V
I (2)
V
I
APPLICATIONS:
•
•
•
•
•
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150°C and a board trace length of 750 mils.
PIN DESCRIPTION
Pin Name
REF
(1)
CLKA1
(2)
CLKA2
V
DD
GND
CLKB1
(2)
CLKB2
(2)
S2
(3)
S1
(3)
CLKB3
(2)
CLKB4
(2)
(2)
Pin Number
1
2
3
4, 13
5, 12
6
7
8
9
10
11
14
15
16
Type
IN
Out
Out
PWR
GND
Out
Out
IN
IN
Out
Out
Out
Out
Out
Functional Description
Input reference clock, 5 Volt tolerant input
Output clock for bank A
Output clock for bank A
3.3V Supply
Ground
Output clock for bank B
Output clock for bank B
Select input Bit 2
Select input Bit 1
Output clock for bank B
Output clock for bank B
Output clock for bank A
Output clock for bank A
Output clock, internal feedback on this pin
CLKA3
(2)
CLKA4
(2)
CLKOUT
(2)
NOTES:
1. Weak pull down.
2. Weak pull down on all outputs.
3. Weak pull ups on these inputs.
2
IDT23S09E
3.3V ZERO DELAY CLOCK BUFFER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
S2
L
L
H
H
S1
L
H
L
H
CLKA
Tri-State
Driven
Driven
Driven
CLKB
Tri-State
Tri-State
Driven
Driven
CLKOUT
(2)
Driven
Driven
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
N
N
Y
N
NOTES:
1. H = HIGH Voltage Level.
L = LOW Voltage Level
2. This output is driven and has an internal feedback for the PLL. The load on this ouput can be adjusted to change the skew between the REF and the output.
DC ELECTRICAL CHARACTERISTICS - COMMERCIAL
Symbol
V
IL
V
IH
I
IL
I
IH
V
OL
V
OH
I
DD_PD
I
DD
Parameter
Input LOW Voltage Level
Input HIGH Voltage Level
Input LOW Current
Input HIGH Current
Output LOW Voltage
Output HIGH Voltage
Power Down Current
Supply Current
V
IN
= 0V
V
IN
= V
DD
Standard Drive
High Drive
Standard Drive
High Drive
REF = 0MHz (S2 = S1 = H)
Unloaded Outputs at 66.66MHz, SEL inputs at V
DD
or GND
I
OL
= 8mA
I
OL
= 12mA (-1H)
I
OH
= -8mA
I
OH
= -12mA (-1H)
—
—
12
32
µA
mA
2.4
—
V
Conditions
Min.
—
2
—
—
—
Max.
0.8
—
50
100
0.4
Unit
V
V
µA
µA
V
OPERATING CONDITIONS - COMMERCIAL
Symbol
V
DD
T
A
C
L
C
IN
Supply Voltage
Operating Temperature (Ambient Temperature)
Load Capacitance < 100MHz
Load Capacitance 100MHz - 200MHz
Input Capacitance
Parameter
Min.
3
0
—
—
—
Max.
3.6
70
30
10
7
pF
Unit
V
°
C
pF
SWITCHING CHARACTERISTICS (23S09E-1) - COMMERCIAL
(1,2)
Symbol
t
1
Output Frequency
Duty Cycle = t
2
÷
t
1
t
3
t
4
t
5
t
6A
t
6B
t
7
t
J
t
LOCK
Rise Time
Fall Time
Output to Output Skew
Delay, REF Rising Edge to CLKOUT Rising Edge
(2)
Delay, REF Rising Edge to CLKOUT Rising Edge
(2)
Device-to-Device Skew
Cycle-to-Cycle Jitter
PLL Lock Time
Parameter
10pF Load
30pF Load
Measured at 1.4V, F
OUT
= 66.66MHz
Measured between 0.8V and 2V
Measured between 0.8V and 2V
All outputs equally loaded
Measured at V
DD
/2
Measured at V
DD
/2 in PLL bypass mode (IDT23S09E only)
Measured at V
DD
/2 on the CLKOUT pins of devices
Measured at 66.66MHz, loaded outputs
Stable power supply, valid clock presented on REF pin
May I ask, what is the link mechanism of lib files like? Is there any information I can check? I did the following test: (1) In a linked file, add uncalled functions and variables. After generating a ...
①The infrared lamp does not light up at night; a. Cause of failure: The switching power supply is abnormal; Troubleshooting: Replace a stable switching power supply (12VDC or 24VAC, I≥2A); b. Cause of...
Saw this on [url=http://www.youtube.com/watch?v=4IQxn85jAKw]youtube[/url]. When DIYing, pay attention to the materials, number of turns, diameter, wire diameter and wire spacing. The magnet is a hard ...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
