EEWORLDEEWORLDEEWORLD

Part Number

Search

EC2500ETTS-53.000M

Description
CRYSTAL OSCILLATOR, CLOCK, 53 MHz, HCMOS/LSTTL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size148KB,6 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance  
Download Datasheet Parametric View All

EC2500ETTS-53.000M Overview

CRYSTAL OSCILLATOR, CLOCK, 53 MHz, HCMOS/LSTTL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN

EC2500ETTS-53.000M Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerECLIPTEK
Reach Compliance Codecompli
Other featuresTRI-STATE; ENABLE/DISABLE FUNCTION; BULK
maximum descent time10 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
JESD-609 codee4
Manufacturer's serial numberEC25
Installation featuresSURFACE MOUNT
Nominal operating frequency53 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeHCMOS/LSTTL
Output load10 LS TTL, 30 pF
physical size7.0mm x 5.0mm x 1.6mm
longest rise time10 ns
Maximum supply voltage5.5 V
Minimum supply voltage4.5 V
Nominal supply voltage5 V
surface mountYES
maximum symmetry60/40 %
Terminal surfaceNickel/Gold (Ni/Au)
EC2500ETTS-53.000M
EC25 00 ET
Series
RoHS Compliant (Pb-free) 5.0V 4 Pad 5mm x 7mm
Ceramic SMD HCMOS/TTL Oscillator
Frequency Tolerance/Stability
±100ppm Maximum
Operating Temperature Range
-40°C to +85°C
Duty Cycle
50 ±10(%)
RoHS
Pb
Nominal Frequency
53.000MHz
TS
-53.000M
Load Drive Capability
Low Drive
Pin 1 Connection
Tri-State (High Impedance)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
53.000MHz
±100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the
Operating Temperature Range, Supply Voltage Change, Ouput Load Change, First Year Aging at 25°C,
Shock, and Vibration)
±5ppm/year Maximum
-40°C to +85°C
5.0Vdc ±10%
50mA Maximum (No Load)
2.4Vdc Minimum with TTL Load, Vdd-0.5Vdc Minimum with HCMOS Load
-16mA
0.4Vdc Maximum with TTL Load, 0.5Vdc Maximum with HCMOS Load
16mA
10nSec Maximum (Measured at 0.4Vdc to 2.4Vdc with TTL Load; Measured at 10% to 90% of waveform
with HCMOS Load)
50 ±10(%) (Measured at 50% of waveform with HCMOS Load or at 1.4Vdc with TTL Load)
Low Drive (10LSTTL Load or 30pF HCMOS Load Maximum)
CMOS
Tri-State (High Impedance)
+2.0Vdc Minimum to enable output, +0.8Vdc Maximum to disable output (High Impedance), No Connect to
enable output.
1pSec Maximum (12kHz to 20MHz offset frequency)
10mSec Maximum
-55°C to +125°C
Aging at 25°C
Operating Temperature Range
Supply Voltage
Input Current
Output Voltage Logic High (Voh)
Input Current Logic High (Ioh)
Output Voltage Logic Low (Vol)
Input Current Logic Low (Iol)
Rise/Fall Time
Duty Cycle
Load Drive Capability
Output Logic Type
Pin 1 Connection
Tri-State Input Voltage (Vih and Vil)
RMS Phase Jitter
Start Up Time
Storage Temperature Range
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
Gross Leak Test
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 1014, Condition A
MIL-STD-883, Method 1014, Condition C
MIL-STD-202, Method 213, Condition C
MIL-STD-202, Method 210
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev M 2/17/2010 | Page 1 of 6
DSP interface
DSP interface...
安_然 DSP and ARM Processors
It turns out that you need to unplug the jtag
When I first used stm32, I found that after downloading the program with the emulator, the program would not run normally if I unplugged the end of the emulator connected to the computer. By chance, I...
ienglgge ARM Technology
How to use FPGA to collect 128KB, 16-bit data?
The input is an analog signal. I found that the built-in ADC of some FPGAs is 12bit, which does not meet the requirements. Can I only input it into the ADC first and then use the FPGA to collect it? W...
SsvepX FPGA/CPLD
TM4C129x development board about reading MX66L51235F EEPROM
During use, the official API (mx66l51235f.h) is called directly, but the configuration fails during the initialization of MX66L51235FInit(ui32SysClock); and it always stays in the Reset_handler sectio...
LLj Microcontroller MCU
Can both crystal radios and operational amplifiers detect RF signals?
Both crystal radios and op amps can detect RF signals? Is that correct?...
雨中 ADI Reference Circuit
WeChat group voice Q&A at 2pm: Vicor power experts answer netizens' power design questions
[align=left][b]Origin of the event:[/b]This Q&A session is an Easter egg after the end of Vicor's theme event "[url=https://www.eeworld.com.cn/huodong/Vicor_PowerAverage_20190318/index.html]Power Supp...
EEWORLD社区 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 840  414  2185  1353  64  17  9  44  28  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号