For small and medium power motor applications, the EPSH-MPC development platform provides current sampling of the isolated analog-to-digital converter AD7403. The external current loop is converted into a corresponding shunt voltage through a shunt resistor and input to the voltage test terminal of the AD7403. The AD7403 outputs according to the clock signal given by CM408F. ADC bit stream, CM408F enables the built-in SINC filter on the input bit stream to calculate the corresponding 16-bit ADC value, and stores the data into the corresponding ring queue through DMA. The host computer software can use the UART-USB port Or obtain the display of data samples through the RS485 port, you can intuitively see the acquisition effect of AD7403, and the collected data can be stored in an excel table to facilitate corresponding analysis of the data.
The reference design is a BLDC motor controller designed to be powered by a single 12V (nominal voltage) supply with a wide voltage range found in typical automotive applications. The board is designed to drive motors in the 60W range, which requires a current of 5 amps. The size and layout of the board facilitates evaluation of the drive electronics and firmware, with easy access to key signals on various test points. A wide variety of motors can be connected by using a 3-contact connector or soldering the motor phase wires to the plated through holes in the board. The 12VDC supply is fused to prevent damage to the board or bench power supply in the event of a motor failure during testing. Commands and the status of the motor can be transmitted through a standard JTAG connector or through PWM input and output signals. The user can also reprogram the microcontroller through the JTAG connector, allowing customization for various applications. This design forms the solution by incorporating the DRV8301-HC-C2-KIT board.
Evaluation board for automotive motor control applications. Ideal for BLDC and PMSM motors, enabling rapid prototyping and evaluation. Covers S12ZVMC256 MagniV products.
42 W Dual Port Isolated Flyback Power Supply with 30 W USB PD 3.0 and 12 W USB-A Port Using InnoSwitch3-Pro with PowiGaN Technology (INN3379C-H302)
The MPC8313E-RDB reference platform is ideal for cost-optimized hardware and software development of networking applications.
500 W motor control power board based on STGIF5CH60TS-L SLLIMM™ Series 2 IPM
Pellicanus is an open source, RP2040-based INS/GNSS module that you can program using MicroPython, C or Rust. It allows you to add Vertical Reference Units (VRU), Attitude and Heading Reference Systems (AHRS), and INS/GNSS capabilities to a variety of platforms: cars, drones, autonomous vehicles, and anything else you need to track. We'll Pellicanus is designed as a 33x30 mm toothed module that can be easily integrated into your project. We also offer carrier boards with a variety of interfaces so you can evaluate the module and start development immediately.
1 kW traction controller reference design for 3-phase BLDC motors for light electric vehicles
Bipolar stepper motor L6208 DMOS driver in PowerDip package evaluation board
This solution uses a PWM module with built-in dead zone control suitable for three-phase motor applications, and is protected by a hardware module to directly shut down the PWM in emergency situations and protect the power transistors from being burned under abnormal operations.
Set of assembled boards for blind-spot detection simulation
ST8500 Programmable Power Line Communications Modem System-on-Chip Evaluation Kit
Low power motor control board with SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B
100 W LED street lighting evaluation board using STLUX385A digital controller
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
