Simple easy to use high side current sense amps protects power supplies as a result of irregular supply voltage caused by short-circuit conditions.
The NXQ1TXH5DB1355 is a debugging board that can be used during the development of applications with the NXQ1TXH5 one chip wireless charging IC
This reference design implements a reinforced isolated three-phase inverter subsystem using isolated IGBT gate drivers and isolated current/voltage sensors. The UCC23513 gate driver used is available in a 6-pin wide body package and LED light analog input, and can be used as a pin-for-pin replacement for existing optically isolated gate drivers. This design shows that the UCC23513 input stage can be driven using all existing configurations for driving optoisolated gate drivers. In-phase shunt resistor based motor current sensing is implemented using the AMC1300B isolated amplifier and DC link voltage, and IGBT module temperature sensing is implemented using the AMC1311 isolated amplifier. This design uses the C2000™ LaunchPad™ to control the inverter.
This solution is designed to create a size-optimized integrated power design for ADAS applications using the TDA3x SoC (no automotive battery input required). By targeting only applications that require lower processing performance, we can select smaller devices and components than systems with higher performance processors.
This reference design demonstrates how to use the IWR6843, a single-chip millimeter wave radar sensor from TI with an integrated DSP, to implement indoor and outdoor people counting applications while enabling sub-1GHz wireless communications. This reference design uses the MMWAVEICBOOST and IWR6843ISK evaluation modules (EVMs) and the LAUNCHXL-CC1352R1 wireless MCU LaunchPadTM. The solution is capable of locating people at distances up to 6 meters (close configuration) and 14 meters (long range configuration).
This PMP10600.1 reference design provides all the power rails required to power the Xilinx® Zynq® 7000 Series (XC7Z015) FPGA. This design uses multiple LMZ3 series modules, multiple LDOs, and a DDR termination regulator. It also has an LM3880 for power-up and power-down sequencing. This design uses a 12V input voltage.
New Analog/Analog Isolator Using Isolated Σ-Δ Modulator, Isolated DC/DC Converter and Active Filter
As China's title of "Infrastructure Maniac" becomes widely known, more and more workers are engaged in dangerous jobs, such as high altitude, underground, tunnels, and engineering vehicles. In order to ensure the safety of these construction workers and ensure timely rescue in the event of an accident, I designed this safety black box for engineering personnel. This equipment can collect the heart rate of construction workers, the temperature and humidity of the surrounding environment, identify the state of movement, and determine whether a fall or collision accident has occurred. It is transmitted to the remote monitoring center through the network. Once the monitoring personnel find an abnormality, they can immediately organize rescue.
84 W isolated flyback power supply for chargers and adapters using PowiGaN-based InnoSwitch3-CP (INN3279C-H218)
Power-over-Ethernet (PoE) technology enables power-sourcing equipment (PSE, a switch/router or midspan system) to deliver up to 15W of power to IEEE® 802.3af-compliant powered devices like IP phones and wireless LAN access points. This application note describes how to design a single-port PSE system to meet the IEEE 802.3af signature, classification, and power-management requirements. The single-port PSE in this example is designed using the MAX5922A IC.
Active Balance chipset used in large lithium-ion batteries provides monitoring, balancing and communication functions. With precise and reliable active balancing, Active Balance BMS enables bidirectional power transfer within each cell. Each EM1401EVM can manage 6 to 14 cells (up to 60V) in Li-ion battery applications. EM1401EVM modules can be stacked up to 1300V. The system provides fast cell balancing, diagnostic functions and modules for controller communication. An independent protection circuit is also provided.
The design converts an 8V-42V DC input into a 5.1V output and is protected by the TPS2546-Q1 programmable current protection switch. Its handshake protocol enables fast charging of smartphones/tablets/handheld devices. By detecting the load current and adjusting the DC/DC output voltage, this design can implement linear USB cable differential compensation function to keep the USB port voltage within a limited range. This design is suitable for devices such as vehicle-mounted hosts and remote USB hubs.
The SimpleLink™ Multi-Standard CC2650 Remote Control Reference Design is an all-in-one solution for the development of voice-based Bluetooth® Low Energy, ZigBee® RF4CE™ or multi-standard remote control. This reference design shows the recommended decoupling and RF layout for optimal RF performance. This design uses discrete components for the balun and filter, as well as an inverted F-shaped PCB antenna to provide good performance at low cost.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
