CN0241

High-side current sensing with input overvoltage protection

Schematic PCB

15kW Vienna-style three-phase rectifier with low-cost mixed-signal control for power factor correction

15 kW, three-phase Vienna rectifier with low cost mixed-signal control for power factor correction

Schematic PCB

Universal power line modem module based on ST7540 PLM and STM32 microcontroller

General purpose power line modem module based on the ST7540 PLM and STM32 microcontroller

Schematic PCB

OM7859: BGA3015 Demonstration Board, 1 GHz 15 dB Gain Broadband Amplifier Application

Schematic PCB

OM7863: BGA3015 Demonstration Board, 5 MHz to 300 MHz 15 dB Gain Inverse Amplifier Application

Schematic PCB

OM17057: Demonstration board for BGU6104 low noise amplifier, ISM and LTE bands

OM7814: GPS Low Noise Amplifier Evaluation Board Using BGU7004

OM7867: BGA3015 Demonstration Board, 40 MHz to 1006 MHz Push-Pull Amplifier Application

Schematic PCB

CN0239

Broadband 6 GHz active mixer with seamless LO interface

Schematic PCB

ST8500 PLC & RF Hybrid Connectivity Development Kit

The EVLKST8500GH hybrid connectivity solution for the ST8500 SoC platform combines the advantages of both PLC and RF technologies to enable applications with the best coverage in any network conditions and topologies.

Schematic PCB

MAXREFDES38#: ECT/EPT current fault sensor

The MAXREFDES38# subsystem reference design is a 3-channel, high-accuracy, low-power analog front-end solution for EPT/ECT and smart-grid current fault-sensing applications. Hardware, firmware, design files, and lab measurements provide complete system information for rapid prototyping and development.

Schematic PCB

12 V-5 W isolated flyback converter based on VIPer122LS

12 V - 5 W isolated flyback converter based on VIPer122LS

Schematic PCB

Lubricating oil detection based on dielectric principle

This design uses LM3S811 as the processor of the lubricating oil dielectric constant detection device, designs the AD5933 impedance measurement circuit, extracts capacitive reactance information from the impedance data, and calculates the change in the lubricating oil dielectric constant based on the change in capacitance to achieve lubrication control. Test the dielectric constant of oil and record the data to find out the change pattern between lubricating oil quality and dielectric constant.

Schematic PCB

CN0148

Layout considerations for a scalable multi-channel simultaneous sampling data acquisition system (DAS) based on the 16-bit 8-channel DAS AD7606

Schematic PCB

MIMXRT1170-EVK: i.MX RT1170 Evaluation Kit

Schematic PCB

Dual Output Isolated PSR Flyback Converter Using VIPER267KDTR for Smart Meters and PLC Systems

Dual Output Isolated PSR Flyback Converter Using VIPER267KDTR for Smart Instruments and PLC Systems

Schematic PCB

OM7868: BGA3018 Demonstration Board, 40 MHz to 1006 MHz Push-Pull Amplifier Application

Schematic PCB

0.7A/1.2V synchronous buck converter with enable function based on ST1S12XX

ST1S12XX based 0.7 A/1.2 V synchronous buck converter with enable function

Schematic PCB

AC current measurement system based on STM32 (program, circuit information)

The overall structure of this design is roughly composed of a main control module, a current signal sampling module, a power module and a serial port output module. In this article, the main control chip uses a microcontroller model STM32F103RC, which makes the structure as small as possible while ensuring the current sampling accuracy. It is as simple as possible, avoids complex and changeable circuit layout, is more convenient for PCB board production, and is relatively low-cost. Among them, in the design of the sampling conditioning circuit, a current transformer is used to sample the current signal.

Schematic PCB

OM7865: BGA3018 Demonstration Board, 40 MHz to 2600 MHz Broadband Amplifier Application

Schematic PCB