CN0171

Low noise, low distortion single-ended input driver circuit for differential input IF sampling ADC

Schematic PCB

KIT9Z1J638EVM: Evaluation Kit - MM9Z1J638, Battery Sensor with CAN/LIN

NXPKIT9Z1J638EVM is a hardware tool for rapid prototyping of current, voltage and temperature sensing applications using MCUs.

Reference design of Epson multimeter microcontroller S1C17M02/M03

Can measure DC/AC voltage, DC/AC current, resistance, inductance, capacitance, diode, frequency. Built-in 16bit ADC, digital filter, RMS effective value circuit and peak hold circuit. Multimeter control unit integrated with microcontroller, officially launched reference design kit, powered by button battery, including schematic diagram.

Schematic PCB

S32K148-Q176 Universal Evaluation Board

The S32K144EVB is a low-cost evaluation and development board for general industrial and automotive applications. Based on the 32-bit Arm® Cortex®-M4F S32K14 MCU, the S32K148EVB provides standard specifications compatible with the Arduino® UNO pin layout, providing a wide range of expansion board options for rapid application prototyping and demonstration.

Schematic PCB

REP014: CDMA PA output power +28.5dBm provides -45dBc ACPR

This reference design (RD) shows how a CDMA PA, the MAX2265, provides -45dBc ACPR at +28.5dBm. Low-cost cellular CDMA power amplifier has good linearity and power-added efficiency for US cellular-band IS-95-based CDMA , PDC, and IS-136-based TDMA modulation formats. Schematics and performance data are shown.

Schematic PCB

REP019: Dual-band front-end CDMA IC tuned to a single 110MHz IF

This application note assesses a tuned, dual-band, front-end CDMA IC with single 110MHZ IF. Focus is on the MAX2322, a low-noise amplifier (LNA) for dual-band CDMA cell-phone handsets. The MAX2323 can also be used in dual-band TDMA, GSM, EDGE, or WCDMA applications.

Schematic PCB

S32K148EVB: S32K148 evaluation board

S32K148 Evaluation Board

MPC574xB/C/G Body, Gateway and Network Evaluation System

Schematic PCB

MTRCKTSPS5604P: 3-phase PMSM development kit using NXP MPC5604P MCU

CN0197

Li-ion battery pack monitor with integrated signal and power isolation

Schematic PCB

MIMXRT1020-EVK: i.MX RT1020 Evaluation Kit

The i.MX RT1020 EVK is an entry-level, low-cost development platform equipped with the i.MX RT1020 crossover processor based on Arm Cortex-M7.

On-board charger (OBC) LLC converter

Tesla Roadster open source design data (battery monitoring board, vehicle display system, HVAC controller, diagnostic software)

Schematic PCB

Using MAX15005 for power supply and driving of LED application systems

This reference design is a complete application design for an automotive LED application. It utilizes the MAX15005 current-mode controller to boost a standard lead-acid car battery to 21V for driving a string of automotive LEDs.

OM13317: NVT2001GM demonstration board

The NVT2008PW (OM13317) and NVT2010PW (OM13324) demonstration boards are designed to allow customers to evaluate NXP's 8- or 10-channel bidirectional voltage level translators.

FRDM-GD3000EVB: Freedom expansion board for GD3000 - BLDC motor pre-driver

The FRDM-GD3000EVB is an easy-to-use board that allows users to practice all functions of the MC34GD3000 pre-driver.

CN0285

Wideband Low Error Vector Magnitude (EVM) Direct Conversion Transmitter

Schematic PCB

FRDM33772BSPIEVB: MC33772 evaluation board with SPI communication

6-channel Li-ion battery controller MC33772 EVB targets automotive and industrial applications with SPI communication

MAX2120 DVB-S Half-NIM Tuner Reference Design

This reference design is a commercial Half-NIM DVB-S tuner that uses Maxim's MAX2120 satellite tuner IC. The reference design connects to the motherboard through a 12-pin connector. The downconverted satellite signal from the LNB is supplied to an active, discrete loop-through, which splits the signal into two paths. One signal goes to the MAX2120 and the other provides an additional output from the STB.

3.3 kW APM OBC Demonstration Board Test Report