TIDA-00827 is an integrated sensor-based BLDC motor controller reference design for low-power, battery-powered brushless DC motor applications. The 8 to 35V operating voltage range supports 3S to 6S lithium polymer battery power supplies. Specific applications include camera heads, low-power fans and robots. The motor controller consists of the MSP430G2353 16-bit, ultra-low power microcontroller and the DRV8313 highly integrated 2.5A triple half-bridge driver. The MSP430G2353 utilizes Hall sensor-based communication feedback to provide the correct drive voltage to the motor through the DRV8313. Onboard potentiometers and buttons provide a simple interface to control the motor.
The PMP10733 uses the LM5160 in a Fly-Buck-Boost topology with the primary side set to a negative voltage. Setting the primary side to a negative voltage reduces the turns ratio of the transformer and therefore allows for better line and load regulation. The primary and secondary voltages are set to negative 15V and positive 15V respectively. The maximum operating current on the primary and secondary voltage rails is set to 150mA. The switching frequency is set to 200kHz.
This reference design functions from a base of silicon carbide (SiC) MOSFETs that are driven by a C2000 microcontroller (MCU) with SiC-isolated gate drivers. The design implements three-phase interleaving and operates in continuous conduction mode (CCM) to achieve a 98.46% efficiency at a 240-V input voltage and 6.6-kW full power. The C2000 controller enables phase shedding and adaptive dead-time control to improve the power factor at light load. The gate driver board (see TIDA-01605) is capable of delivering a 4-A source and 6-A sink peak current. The gate driver board implements a reinforced isolation and can withstand more than 100-V/ns common-mode transient immunity (CMTI). The gate driver board also contains the two-level turnoff circuit, which protects the MOSFET from voltage overshoot during the short-circuit scenario.
The TIDA-00792 TI Design provides monitoring, balancing, primary protection and gauging for a 12 to 15 cell lithium-ion or lithium-iron phosphate based batteries. This board is intended to be mounted in an enclosure for industrial systems. The reference design subsystem provides battery protection and gauging configuration with parameters avoiding code development and provides high side protection switching to allow simple PACK- referenced SMBus communication for battery status even while protected.
Texas Instruments' ZLLRC reference design enables simple and direct control of lights connected to a ZigBee Light Link network. It is designed to control a subgroup of lights on that network, such as the lights in a room in your home. It creates its own group containing lights that have touch connections to it. These lights can be added/removed later. It has 14 buttons to control status (on/off), hue, saturation, level, target selection and scene. ZLLRC is supported by Z-Stack Lighting version 1.0.2 and higher. It is based on the CC2530 system-on-chip (SoC) with integrated ZigBee radio. It connects to the onboard PIFA PCB antenna through an integrated balun. To extend battery life, the TPS62730 DCDC converter can be used to convert the CR2025 battery voltage to 2.1 V.
This BoosterPack package contains an "EM Adapter BoosterPack". The purpose of this EM adapter board is to provide an easy-to-use bridge between any TI MCU LaunchPad and various TI RF Evaluation Modules (EMs), such as the CCxxxx Low Power RF Evaluation Modules. No specific software is provided, so it is the user's responsibility to write the appropriate code to interface between the MCU and the RF device.
The TIDA-00136 reference design is a high-speed serial video interface that allows remote automotive WVGA TFT LCD displays using the OpenLDI (LVDS) interface to be connected to a video processing system. This design uses TI's FPD-Link II SerDes technology to transmit uncompressed video data over shielded twisted pair or coaxial cable. Examples of applications include rear-seat entertainment systems, automotive instrument clusters and head unit displays. This design combines the DS99R421Q1-EVK and DS90UR124-Q1 boards to form the solution.
This reference design implements and measures a complete 120MHz high-bandwidth optical front-end consisting of a high-speed transimpedance amplifier, a fully differential amplifier, and a high-speed 14-bit 160MSPS ADC with JESD204B interface. The design provides hardware and software to evaluate the system's response to high-speed optical pulses generated by the included laser driver and diode, suitable for applications with optical time domain reflectometry (OTDR).
This analog front end (AFE) design shows how to connect two or more Σ-Δ ADCs for simultaneous sampling and how to expand the number of input channels to provide maximum flexibility. Precision current measurement is achieved by connecting the AFE to a current transformer (CT) and a Rogowski coil. Likewise, accurate voltage measurements are achieved using resistive voltage dividers without and with isolation amplifiers. The AFE can be configured to measure unipolar or bipolar inputs. The required power is provided onboard. Additionally, diagnostics can be integrated into one design, as shown in TIDA-00810.
Vienna rectifier power topology is used in high power three phase power factor (AC-DC) applications such as off board EV chargers and telecom rectifiers. Control design of the rectifier can be complex. This design illustrates a method to control the power stage using C2000™ microcontrollers (MCUs). It also enables monitoring and control of Vienna rectifier based on the HTTP GUI page and Ethernet support(F2838x only).The hardware and software available with this design helps accelerate your time to market.Vienna rectifier power topology is used in high power three phase power factor correction applications such as off board Electric Vehicle Charging and telecom rectifiers. This design illustrates how to control a vienns rectifier using C2000 Microcontroller. Vienna rectifier power topology is used in high power three phase power factor (AC-DC) applications such as off-board electric vehicleEV chargers and telecom rectifiers. Control design of the rectifier can be complex. This design illustrates a method to control the power stage using C2000™ microcontrollers. The hardware and software available with this design helps accelerate your time to market.The Vienna rectifier power topology is used in high power three phase power factor correction applications such as off-board electric vehicle charging and telecom rectifiers. This design illustrates how to control a Vienna rectifier using C200-MCU.
The efficiency and diagnostic capabilities required for automotive emergency call (eCall) systems create unique requirements for the audio subsystem, such as speaker diagnostics and low power consumption. This TI reference design shows how TI's automotive dual-channel audio codec (TLV320AIC3104-Q1) and Class D audio amplifier (TAS5411-Q1) can be used in eCall applications.
This fully tested reference design demonstrates a low-power solution for electronic measurement of water flow with a mechanical flow meter and provides a single-chip platform for water flow measurement and wireless communications. The design is ideal for automatic water meter reading (AMR) modules, which add wireless communications capabilities to existing mechanical flow meters. The radio frequency subsystem supports standard protocols such as wireless M-Bus or proprietary protocols in the sub-1GHz ISM band. This reference design provides the ability to accurately read mechanical rotation over long distances and provides greater reliability. Ultra-low power consumption reduces battery requirements and extends product life.
This reference design is an automotive-qualified isolated gate driver solution that drives silicon carbide (SiC) MOSFETs in a half-bridge configuration. This design provides two push-pull bias supplies for dual-channel isolated gate drivers, each providing +15V and –4V output voltages and 1W output power. The gate driver is capable of 4A peak source current and 6A peak sink current. The driver implements reinforced isolation and can withstand 8kV peak isolation voltage and 5.7kV RMS isolation voltage as well as common-mode transient immunity (CMTI) of over 100V/ns. This reference design includes a two-stage shutdown circuit that protects the MOSFET against voltage overshoot during short circuit conditions. DESAT detection threshold and second stage shutdown delay time are configurable. This design uses an ISO7721-Q1 digital isolator to connect the fault and reset signals. The overall design adopts a compact double-layer PCB board of 40mm × 40mm.
This TI reference design provides a low-component-count, low-cost solution for a 4 to 20mA loop-powered resistance temperature detector (RTD) temperature transmitter. The design utilizes the on-chip smart analog combination module in the MSP430FR2355 MCU to control the loop current, thus eliminating the need for a separate DAC. The design achieves 12-bit output resolution and 6µA output current resolution. The design incorporates reverse polarity protection as well as IEC61000-4-2 and IEC61000-4-4 protection on the loop power input.
This 6cm motor is packaged and ready; connect to power and run! The simple and reliable design is easily modified to support speed and current system needs. The DRV5013 Hall-effect sensor senses the magnetic rotor position, and the DRV8307 controller determines when to drive the CSD88537ND FET that energizes the coil .
The Acontis EC-Master EtherCAT Master stack is a highly portable software stack that can be used on a variety of embedded platforms. EC-Master supports high-performance TI Sitara MPUs and provides an advanced EtherCAT Master solution that customers can use to implement EtherCAT communication interface boards, EtherCAT-based PLCs or motion control applications. The EC-Master architecture is designed so that users do not need to plan additional tasks, so the full stack functionality is available even on platforms without an operating system (such as TI Starterware supported on AM335x). This architecture combined with high-speed Ethernet drivers allows users to implement EtherCAT master on the Sitara platform with very short cycle times of 100 microseconds or less.
The TIDA00255 reference design utilizes the bq76940 analog front end (AFE) IC. It can measure battery voltage, mold temperature or external thermistor voltage using a 14-bit ADC. Current is measured individually by a separate 16-bit coulomb counter. The design turns off the low-side power FET to stop discharging or charging based on selected hardware limits. A microcontroller not included in this design will be part of the battery controller to communicate with the AFE to set protection thresholds, enable the power FETs, provide fault recovery, and shut down the FETs during over/under temperature conditions. Battery controller designs may include additional features that are not part of this reference design, such as secondary overvoltage protection, measurement, and isolated communications to inform the system of battery status.
This antenna board reference design contains multiple low-cost antenna solutions for sub-1 GHz and 2.4 GHz short-range wireless systems.
TIDA-00447 is a 24V, dual brushless DC (BLDC) motor drive reference design that can be used to drive circulating water pumps and drain pumps in dishwashers. The circulating water pump and drainage pump drive stages are designed for continuous operation of 100W and 30W respectively. The drain pump driver is based on a single-chip, low external component count three-phase motor driver with integrated power MOSFETs and provides a proprietary sensorless control scheme enabling continuous sine wave drive. In addition, it features an integrated buck/linear regulator that efficiently reduces the supply voltage to 5V or 3.3V to power internal and external circuitry. The circulating water pump is implemented using a discrete solution with MCU, external MOSFET driver with protection mechanism and current sensing function, and external power MOSFET. This architecture allows the flexibility to adjust drive power levels as needed. The MCU is programmed through the InstaSPIN-BLDC software, which enables sensorless trapezoidal control of the BLDC motor using an anti-EMF integration approach, and can also be used to configure and control the speed of the drainage pump stage. A separate UART interface allows the drive unit to communicate with the main user interface controller. This reference design has been fully tested with current and motor stop protection mechanisms operating at full load.
PMP9750 is a CLL resonant converter reference design with an input voltage of 400VDC and an output voltage of 28V/9A. Unlike the LLC series of resonant converters, the CLL resonant converter used in the PMP9750 utilizes its output inductor to minimize the size of the resonant tank. With the resonant controller UCC25600 and bridge driver UCC27714, the PMP9750 achieves a peak efficiency of 95.7%.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
