CN0229

4-channel, flexible, configurable, voltage and current output circuit for I/O card and PLC applications

Schematic PCB

Single op amp demonstration board for SC70 or SOT-23 packages

Single op amp demo board, SC70 or SOT-23 package

Schematic PCB

For FXLN83xxQ NXPBreakout board for acceleration sensor

BRKOUT-FXLN83xxQ kit includesBreakout board for the FXLN83xxQ acceleration sensor series.

Rod strain gauge

DAQ on a Stick Strain Gauge with Programmable Chopper Stabilized In Amp

ERASynthMicro: USB powered, portable, open source, RF signal generator, supports 12.5MHz - 6.4GHz

It can be powered via a USB port and has an LCD interface for standalone use without a PC. ERASynth Micro uses a dual-loop PLL architecture to provide fast frequency switching and fine tuning resolution. Frequency, amplitude and pulse modulation capabilities are also available.

Schematic PCB

Low-side current sensing evaluation board based on TSZ121 op amp

Low-side current sensing evaluation board based on TSZ121 op amp

Schematic PCB

Dual op amp series bare PCB evaluation board for MSO8 package

Dual operational amplifier series bare PCB evaluation board, MSO8 package

Schematic PCB

Dual op amp series bare PCB evaluation board for MSO10 package

Dual op amp series bare PCB evaluation board, MSO10 package

Schematic PCB

Dual op amp series bare PCB evaluation board for DFN8 package

Dual operational amplifier series bare PCB evaluation board, DFN8 package

Schematic PCB

SO8 packaged single-channel operational amplifier demonstration board

Single Channel Op Amp Demonstration Board, SO8 Package

Schematic PCB

Dual op amp series bare PCB evaluation board for DFN8-EP package

Dual operational amplifier series bare PCB evaluation board, DFN8-EP package

Schematic PCB

CN0219

^{Adopt ADAV801/ADAV803 audio codec to implement S/PDIF and I 2} S interface with SigmaDSP codec

Schematic PCB

Laser projector project made by teacher ChaN

Dual op amp series bare PCB evaluation board for SO8 package

Dual operational amplifier series bare PCB evaluation board, SO8 package

Schematic PCB

CN0105

16-bit 10 MSPS ADC AD7626 single-ended to differential high-speed drive circuit

Schematic PCB

CN0269

18-bit, 1.33 MSPS, 16-channel data acquisition system

Schematic PCB

AIS2IH adapter board for standard DIL 24 sockets

he STEVAL-MKI218V1 is an adapter board designed to facilitate the evaluation of MEMS devices in the AIS2IH product family.

Schematic PCB

CN0251

24-bit, 4.7 Hz, 4-channel analog data acquisition system

Schematic PCB

Accurate point cloud generation using DLP technology for 3D machine vision applications

The 3D machine vision reference design uses Texas Instruments' DLP software development kit (SDK), allowing developers to easily build by integrating TI's digital micromirror device (DMD) technology with cameras, sensors, motors and other peripherals 3D point cloud. Highly differentiated 3D machine vision systems leverage the DLP® LightCrafter™ 4500 Evaluation Module (EVM) powered by the DLP® 0.45-inch WXGA chipset to provide the flexibility to control high-resolution, accurate graphics for industrial, medical and security applications.

Schematic PCB

Output Short-Circuit Protection Reference Design for TPS61088 Boost Converter

This reference design provides an output short-circuit protection solution for the TPS61088 boost converter. This function is implemented through the overcurrent protection (OCP) circuit. When the output is shorted to ground or the load current is higher than a certain value, the OCP circuit will disconnect the TPS61088 from the corresponding load. This solution only requires an additional low-cost comparator, a sensing resistor and a small N-MOSFET. By adding this small amount of circuitry, the TPS61088 is protected from output short circuit and overload conditions.

Schematic PCB