RDDRONE-T1ADAPT: Ethernet media converter for drones, rovers, mobile robots and cars

CN0335

12-Bit, 300 kSPS, Single Supply, Fully Isolated Data Acquisition System for ±10 V Input

Schematic PCB

OM13529UL: PCAL6524/(EV-VFBGA36)(S500)Fm+ I2C 24-bit GPIO Demonstration Board

Compact Full HD 1080p (up to 16 Amp) projection display reference design with DLP Pico technology

This reference design features the DLP Pico™ 0.47-inch TRP Full HD 1080p display chipset and is implemented in the DLP LightCrafter Display 4710 G2 Evaluation Module (EVM), supporting use in accessory projectors, screenless displays, interactive displays, wearable devices including Full HD resolution is used in projection display applications such as head-mounted displays, signage, industrial and medical displays. The chipset used in this reference design consists of the DLP4710 (0.47 1080p) DMD, DLPC3439 display controller, and DLPA3005 PMIC/LED driver.

Schematic PCB

1-Wire Bidirectional Level Translator (1.8V to 5V) Reference Design

Designers need open-drain logic to run at 1.8V at the 1-Wire master IO. Most 1-Wire slave devices cannot run at 1.8V. This application note presents an RD (reference design) of a circuit that translates from a 1.8V 1-Wire master to a 5V 1-Wire slave device. The RD is used for driving typical 1-Wire slave devices. The MAX3394E voltage-level translator is featured in the design.

ADTJA1101-RMII: TJA1101 Automotive Ethernet Adapter for S32K148EVB and i.MX8

The humidity and temperature sensor nodes of the star network achieve a service life of button batteries of more than 10 years

This TI design uses Texas Instruments' nanopower system timers, SimpleLink™ ultra-low power wireless microcontroller (MCU) platform, and humidity sensing technology to demonstrate an ultra-low power approach to driving a sensor end node. These technologies enable extremely long battery life: more than 10 years on a standard CR2032 lithium-ion coin cell battery. This TI Design includes system design techniques, detailed test results, and information to get your design started and up to speed.

Schematic PCB

OM6270: SPI/I ² C to UART Bridge Demonstration Board (SC16IS750)

OM6270 is a demonstration board for SC16IS750. SC16IS740/750/760 is a slave I ² C bus/SPI interface that connects to a single-channel high-performance UART .

CN0294

Increase the number of clock source outputs using low-jitter LVPECL fanout buffers

Schematic PCB

OM13790 Host & Dock: USB Type-C Shield Board Gen 2 with Display Port Alt Mode

The NXP Gen 2 USB Type-C shield works with the MCUXpresso SDK and USB power delivery stack, giving you access to your choice of Kinetis®, LPC and i.MX RT development platforms via the USB Type-C connector. And it uses NXP’s easy-to-use hardware and MCUXpresso software and tools (the only similar solution on the market) to shorten the learning curve. It enables Type-C to seamlessly support Display Port alt mode and provides extensive overvoltage protection services for a simple and efficient design.

CANable: A small, low-cost, open-source USB-to-CAN adapter based on stm32f0

CANable 2.0 is a small, low-cost, open-source USB to CAN adapter. CANable enumerates as a virtual serial port on your computer and acts as a serial line to CAN bus interface. Using the alternative candleLight firmware, CANable enumerates as a native CAN interface on Linux. CANable 2.0 supports standard CAN and CAN-FD.

The CANable adapter is compatible with ARM-based embedded platforms such as Raspberry Pi, Raspberry Pi Zero, ODROID, BeagleBone, etc., making it ideal for integration into OEM products.

Schematic PCB

MAXREFDES63#: 8-channel digital output micro PLC card

The MAXREFDES63# reference design ushers in the era of Industry 4.0. This design meets the higher voltage needs of industrial control and industrial automation applications, while consuming minimal power and space. This high-performance system features eight channels of digital outputs and a complete, efficient power-supply system. Hardware and firmware design files are provided.

4 W/400-470 MHz reference design using PD84001 + PD84008L-E + LPF

4 W/400 - 470 MHz reference design using PD84001 + PD84008L-E + LPF

Schematic PCB

PD85050S based RF power amplifier for mobile radio applications

PD85050S based RF power amplifier for mobile radio applications

Schematic PCB

OpenEarable open source in-ear wireless headphones (finished version)

OpenEarable aims to enable ear-based sensing applications by providing a flexible open source hardware platform. It integrates a range of sensors, including a 9-axis inertial measurement unit, ear canal pressure and temperature sensors, inward-facing ultrasound microphone, speakers, buttons and controllable RGB LEDs. With these capabilities, OpenEarable provides researchers and developers with the ability to explore a variety of application scenarios.

OpenEarable controls and transmits sensor data via BLE (Bluetooth Low Energy). Audio is played from or recorded to the internal SD card. OpenEarable is compatible with the provided dashboard and Edge-ml.

Schematic PCB

CN0197

Li-ion battery pack monitor with integrated signal and power isolation

Schematic PCB

160 W + 160 W Dual BTL Class D Audio Amplifier Demonstration Board Based on TDA7498E

160 W + 160 W Dual BTL Class D Audio Amplifier Demonstration Board Based on TDA7498E

Schematic PCB

Microphone evaluation board based on MP34DT05-A digital MEMS

Microphone add-on board based on MP34DT05-A digital MEMS

Schematic PCB

Open source USB2.0 high-speed analyzer

The analyzer host computer directly uses Wireshark. The hardware is implemented using Cypress CY7C68013A MCU + Lattice LCMXO2 FPGA + Microchip USB3343 USB PHY

Schematic PCB

OM13317: NVT2001GM demonstration board

The NVT2008PW (OM13317) and NVT2010PW (OM13324) demonstration boards are designed to allow customers to evaluate NXP's 8- or 10-channel bidirectional voltage level translators.