CN0218

500 V common mode voltage and current monitor

Schematic PCB

CN0235

Fully isolated lithium-ion battery monitoring and protection system

Schematic PCB

CN0241

High-side current sensing with input overvoltage protection

Schematic PCB

CN0260

Oversampled SAR ADC using PGA achieves over 125 dB dynamic range

Schematic PCB

CN0197

Li-ion battery pack monitor with integrated signal and power isolation

Schematic PCB

CN0177

18-Bit, Linear, Low-Noise, Precision Bipolar ±10 V DC Voltage Source

Schematic PCB

CN0175

Low-cost, 8-channel, simultaneous sampling data acquisition system with 84 dB SNR and excellent channel-to-channel matching

Schematic PCB

CN0160

Universal Serial Bus (USB) Peripheral Isolator Circuit

Schematic PCB

CN0159

Universal Serial Bus (USB) Cable Isolator Circuit

Schematic PCB

CN0158

Universal Serial Bus (USB) Hub Isolator Circuit

Schematic PCB

CN0157

Universal Serial Bus (USB) Hub Isolator Circuit

Schematic PCB

CN0148

Layout considerations for a scalable multi-channel simultaneous sampling data acquisition system (DAS) based on the 16-bit 8-channel DAS AD7606

Schematic PCB

Calibration system for pressure transmitter based on AD855X programmable gain amplifier

This reference design addresses this need for pre-factory calibration and provides a complete multi-channel fully automatic calibration system for pressure transmitter calibration before leaving the factory.

Schematic PCB

Three-phase energy meter based on ADE7878

ADI's high-precision, three-phase power measurement chip ADE7878 is used for power measurement, including measurement of active, reactive and apparent power. It realizes the functions of voltage and current effective value measurement, power factor measurement and other functions.

Schematic PCB

Intelligent electronic device (IED) system based on IEC61850

Smart grid can improve the efficiency, reliability, and economy of power generation and distribution through a high degree of automation of the power system to ensure the sustainable development of the power network. Intelligent electronic devices (IEDs) are the basic elements of smart grids, providing the detection, measurement, protection and control functions required by the system.

Schematic PCB

1/8 brick power module based on ADP1051

The 1/8 brick power module in this reference design is designed based on the 1/8 brick power supply standard defined by the Distributed Power Open Standards Alliance (DOSA). This power module uses an Analog Devices ADP1051 to control the energy conversion from input to output.

Schematic PCB

High-efficiency and low-cost 400W power supply design based on ADP1051

This reference design uses the ADP1051, a newly launched low-cost and highly integrated power supply chip from ADI, to control the energy conversion from input to output. This power supply design comprehensively considers factors of efficiency and cost, and designs a solution with optimal efficiency and cost at the 400W power level. It is suitable for power amplifier power supply systems of wireless communication base stations and railway power supply systems in the industrial field.

Schematic PCB

ADSP-CM408F power distribution automation solution

The ADSP-CM40X series of processor chips are the latest products launched by ADI based on the ARM Cortex M4 core. The product's processor has a main frequency of up to 240Mhz, integrates a high-performance 16bits ADC, harmonic analysis engine (HAE) and rich memory and external interface resources. It is very suitable for medium and low-voltage relay protection products, distribution automation terminals, and motors. Servo drive control and other applications.

Schematic PCB

Motor control system based on ADSP-CM408

For motor control systems, ADI can provide complete solutions covering all important devices in the signal chain. Related products include analog-to-digital/digital-to-analog converters, amplifiers, embedded processors, iCoupler® digital isolators and power management devices. These high-performance devices and increased system integration help achieve newer topology designs and bring value to customers' differentiated system designs.

Schematic PCB

Motor current detection system solution based on ADSP-CM408 and AD7403

For small and medium power motor applications, the EPSH-MPC development platform provides current sampling of the isolated analog-to-digital converter AD7403. The external current loop is converted into a corresponding shunt voltage through a shunt resistor and input to the voltage test terminal of the AD7403. The AD7403 outputs according to the clock signal given by CM408F. ADC bit stream, CM408F enables the built-in SINC filter on the input bit stream to calculate the corresponding 16-bit ADC value, and stores the data into the corresponding ring queue through DMA. The host computer software can use the UART-USB port Or obtain the display of data samples through the RS485 port, you can intuitively see the acquisition effect of AD7403, and the collected data can be stored in an excel table to facilitate corresponding analysis of the data.

Schematic PCB