CN0325

PLC/DCS universal analog input using 4-pin or 6-pin terminal strip

Schematic PCB

OM13529UL: PCAL6524/(EV-VFBGA36)(S500)Fm+ I2C 24-bit GPIO Demonstration Board

RDDRONE-T1ADAPT: Ethernet media converter for drones, rovers, mobile robots and cars

1-Wire Bidirectional Level Translator (1.8V to 5V) Reference Design

Designers need open-drain logic to run at 1.8V at the 1-Wire master IO. Most 1-Wire slave devices cannot run at 1.8V. This application note presents an RD (reference design) of a circuit that translates from a 1.8V 1-Wire master to a 5V 1-Wire slave device. The RD is used for driving typical 1-Wire slave devices. The MAX3394E voltage-level translator is featured in the design.

ADTJA1101-RMII: TJA1101 Automotive Ethernet Adapter for S32K148EVB and i.MX8

CN0335

12-Bit, 300 kSPS, Single Supply, Fully Isolated Data Acquisition System for ±10 V Input

Schematic PCB

Compact Full HD 1080p (up to 16 Amp) projection display reference design with DLP Pico technology

This reference design features the DLP Pico™ 0.47-inch TRP Full HD 1080p display chipset and is implemented in the DLP LightCrafter Display 4710 G2 Evaluation Module (EVM), supporting use in accessory projectors, screenless displays, interactive displays, wearable devices including Full HD resolution is used in projection display applications such as head-mounted displays, signage, industrial and medical displays. The chipset used in this reference design consists of the DLP4710 (0.47 1080p) DMD, DLPC3439 display controller, and DLPA3005 PMIC/LED driver.

Schematic PCB

OM6270: SPI/I ² C to UART Bridge Demonstration Board (SC16IS750)

OM6270 is a demonstration board for SC16IS750. SC16IS740/750/760 is a slave I ² C bus/SPI interface that connects to a single-channel high-performance UART .

MAXREFDES82#: Intelligent pressure sensor

The MAXREFDES82# reference design is an industrial, smart force sensor. Four load cells mounted on a quadrant plane are channeled to a multi-channel 24-bit ADC and the conversion results are computed to indicate the force magnitude, position and movement on a flat cover.

Schematic PCB

OM13790 Host & Dock: USB Type-C Shield Board Gen 2 with Display Port Alt Mode

The NXP Gen 2 USB Type-C shield works with the MCUXpresso SDK and USB power delivery stack, giving you access to your choice of Kinetis®, LPC and i.MX RT development platforms via the USB Type-C connector. And it uses NXP’s easy-to-use hardware and MCUXpresso software and tools (the only similar solution on the market) to shorten the learning curve. It enables Type-C to seamlessly support Display Port alt mode and provides extensive overvoltage protection services for a simple and efficient design.

MAXREFDES60#: 16-bit analog output micro PLC

The MAXREFDES61# reference design ushers in the era of Industry 4.0. With a complete analog front-end for the next generation of ultra-small programmable logic controllers, this design meets the higher resolution and higher voltage needs of industrial control and industrial automation applications, while consuming minimal power and space. This high-performance system features four channels of analog input, a complete, efficient power-supply system and on-board processing. Hardware and firmware design files as well as FFTs and histograms from lab measurements are provided.

Schematic PCB

Altitude pressure experiment design board

DEMOAPEXSENSOR is an experimental demonstration board dedicated to pressure sensors for various applications.

FREMONT (MAXREFDES6#): 16-bit, high-precision, 0 to 100mV input, isolated analog front end (AFE)

The Fremont (MAXREFDES6#) subsystem reference design meets the high-resolution needs of low-voltage output sensor applications. Boards for purchase, hardware and firmware design files, and FFTs and histograms from lab measurements provide complete system information for rapid prototyping and development.

Schematic PCB

Campbell (MAXREFDES4#): 16-bit, high-accuracy 4-20mA input isolated analog front end (AFE)

This document explains how the Campbell (MAXREFDES4#) subsystem reference design meets the higher resolution and isolation needs of industrial control and industrial automation applications. Hardware and firmware design files as well as FFTs and histograms from lab measurements are provided.

Schematic PCB

MAXREFDES63#: 8-channel digital output micro PLC card

The MAXREFDES63# reference design ushers in the era of Industry 4.0. This design meets the higher voltage needs of industrial control and industrial automation applications, while consuming minimal power and space. This high-performance system features eight channels of digital outputs and a complete, efficient power-supply system. Hardware and firmware design files are provided.

Laptop VGA signal switching reference design

This application shows how the MAX4885E low-capacitance VGA switch can be used to perform the switching function in a laptop computer. The MAX4885E draws nearly zero current, fits into a 4mm x 4mm package, and incorporates most of the switches and active components used in a discrete implementation. All device outputs are protected to ±15kV Human Body Model (HBM) so that the designer can eliminate many ESD components, thereby reducing cost and saving board space. An application circuit shows the MAX4885E used for VGA signal switching between a laptop and docking station.

MAXREFDES77#: Dual-channel current sensing peripheral module

This reference design demonstrates the performance of the MAX44285 dual-channel, high-precision, high-voltage, current-sense amplifier. It is a Pmod module that contains all the necessary circuitry required for the design of a current and temperature monitoring system.

Schematic PCB

CN0197

Li-ion battery pack monitor with integrated signal and power isolation

Schematic PCB

OM13317: NVT2001GM demonstration board

The NVT2008PW (OM13317) and NVT2010PW (OM13324) demonstration boards are designed to allow customers to evaluate NXP's 8- or 10-channel bidirectional voltage level translators.

Health sensor platform

Maxim health sensor (hSensor) platform helps customers evaluate Maxim's complex and innovative medical and high-end fitness solutions faster and easier. The hSensor platform supports the measurement of motion, precision skin temperature, biopotential measurements, and reflective photo plethysmography measurements, etc. The hSensor comes with a PC graphical user interface (GUI) application and Android application for customers to evaluate the sensors and other devices on the board. Hardware files and firmware source code provide complete documentation for the design. The board is also available for purchase.